Rupes LHR21ES Traduccion Del Manual De Instrucciones Originale página 6

TECHNICAL SPECIFICATIONS
TYPE
Ø POLISHING FOAM mm
Ø BACKING PAD mm
Ø ORBIT mm
POWER
R.P .M.
WEIGHT
ELECTRONIC SPEED CONTROL
INSULATION CLASS
The values shown are based on a nominal voltage of 230V/50Hz. In the case of voltages and frequencies of different power values may vary. Refer to the label technical
specifications to the nominal values of the tool.
PICTOGRAPH
Read the following instruction first before operating
the product.
Important safety indications
Use personal protective equipment.
Double insulated tool.
INSULATION CLASS II
CE compliant
WARNINGS
The safety and accident prevention instructions are
reported in the "SAFETY INSTRUCTION" booklet which
is an integral part of these documents. This operating
instructions manual indicates the additional information
required for the specific use of the tool.
CORRECT USAGE
This tool is designed to be used as a polisher. Read
all the warnings, instructions, indications provided
on drawings and specifications supplied with this
tool. Failure to comply with all the instructions provided
below may cause electrical shocks, fire and/or serious
injuries.
This tool is not intended to be used for smoothing,
metal brushing and cutting operations. The use of this
tool for unintended applications may cause hazards and
injuries to people.
The tool must be used with accessories that have
been specifically designed or recommended by the
manufacturer. The fixing of the accessory to the tool
does not guarantee a safe operation.
The rated speed of the accessories must be at least
equivalent to the maximum speed specified on the
tool. Using the accessories at speeds above the rated
one, may cause them to break or be projected into the air.
The external diameter and thickness of the
accessories must match the specifications of the
tool. Accessories with incorrect dimensions cannot be
adequately protected or controlled.
The configuration of accessories must match the tool.
The use of accessories that cannot be perfectly fitted on
the tool may result in imbalance, excessive vibrations
and in the impossibility of controlling the tool.
LHR 21ES
180
150
21
500
2000 ÷4200
2,60
•
II
Do not use damaged accessories. Before use, inspect
all the accessories. Inspect the supporting pads and
verify there are no cracks, tears or excessive wear. If
the tool or accessory has fallen, verify that it is not
damaged or install a new accessory. After inspecting
or installing an accessory, test the operation of the tool
at maximum speed and without load for one minute,
keeping at a safety distance. If the accessories are
damaged, they will break during this test.
STARTING UP
Voltage and power frequency must match the data
displayed on the identification plate (1). Make sure
that tool is switched off before plug is connected.
TOOL ASSEMBLY
Position the cap (7) on the gearbox such that the holes
for mounting the screws (5) are aligned with those on
the gearbox.
ACCESSORIES ASSEMBLY
BACKING PAD (Pic 1 to Pic 4)
- Place the disc pad (9) in the centre;
- slightly turn the disc pad (9) until it is fixed to the screw;
- tighten the disc pad fixing screw using the supplied
disc pad Allen wrench (10). Do not tighten the disc
pad if it is in the wrong position.
- lubricate the rubber shroud (11) with non-silicone
based products.
- ordinary maintenance: it 's necessary to periodically
check the correct tightening of the screw (4) of the
backing pad using the wrench supplied (10)
POLISHING FOAM
Apply pressure on polishing pad to join pad to plate (8).
START AND STOPPING
- Starting: push the lever of the switch (2) towards the
body of the tool; if the tool is to be locked in the ON
position, press button (11) at the same time and keep
it pressed while releasing lever (2), thus locking the
switch.
- Stopping: release the lever of the switch or, if locked
in position, push the lever to release the lock button.
The tool continues to rotate after it is turned off.
ENGLISH
6
LHR 15ES
150
125
15
500
2000÷5000
2,50
•
II