Rupes LHR21ES Traduccion Del Manual De Instrucciones Originale página 7

Do not empty the tool with the polishing pad still
mounted. In this way, the polishing pad may be
subject to lacerations
SELECTING RPM
The rpm can be adjusted by rotating the wheel (3). The
choice of speed depends on the characteristics of the
abrasive disc and the material to be worked.
ACCESSORIES DISASSEMBLY
BACKING PAD
Unscrew pad's (4-9) mounting screw using the wrench
(10).
POLISHING FOAM
Remove the polishing foam used and apply the new one
with pressing on the backing pad.
ALLOWED ACCESSORIES
LHR 21ES: polishing foam Ø 180 mm for backing pad
Ø 150 mm.
LHR 15ES: polishing foam Ø 150 mm for backing pad
Ø 125 mm.
NOISE EMISSION VALUES
Detected noise emission values comply with the
following directives: EN 62841
SOUND PRESSURE LEVEL
SOUND POWER LEVEL
UNCERTAINTY (K)
Use ear protection!
VIBRATION EMESSION VALUES
Detected vibration emission values comply with the
following directives: EN 62841
3 AXIS VIBRATION LEVEL
UNCERTAINTY (K)
Displayed emission values are comparative and are to be
employed for a provisional assessment of the operator's
risk exposure during the work period. Appropriate
evaluation of work period must also include tool's idle
and stop periods. These emission values represent the
tool's main applications. If the tool is used for other
applications, with other accessories, or if it does not
undergo regular maintenance, emission values can
significantly increase during operations.
Danger! The indicated measurements refer to
new power tools. Daily usage causes the noise
and vibration values to change.
MAINTENANCE
All maintenance operations are carried out with the
LHR 21ES
dB(A) 77
dB(A) 88
dB(A) 3
LHR 21ES
m/s 2.7
2
m/s 1.7
2
power supply disconnected. At the end of each work
session, or when required, remove any dust from the
body of the tool using a jet of compressed air, paying
particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken
by the user.
Maintenance and cleaning of the inner parts, like
brushes, ball bearings, gears etc. or others, must be
carried out only by an authorized customer-service
workshop.
DISPOSAL (WEEE DIRECTIVE)
For EU countries only: According to the European
Directive on Waste from electrical and electronic
equipment and its implementation in conformity
with national standards, exhausted electrical equipment
must be collected separately, in order to be recycled in an
environmentally friendly way. The product, when it
reaches the end of its life, must not be dispersed in the
environment or thrown away as household waste. It must
be disposed at authorized recycling centres (contact your
local authorities to know where to dispose of the product
according to the law). The correct disposal of the product
contributes to the health and preservation of the
environment.
Illegal disposal of the product will entail penalties against
the offenders.
LHR 15ES
77
CONFORMITY DECLARATION
88
3 We declare on our responsibility that the represented
tool is in conformity with the directives:
2006/42/EC, 2014/30/EU, 2011/65/EU.
The tests have been carried out in accordance with
standard:
EN 62841-1: 2015 + AC:2015
EN 62841-2-4: 2014 + AC:2015
LHR 15ES
EN 55014-1: 2017
2.7
EN 55014-2: 2015
1.5
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 62233: 2008
EN IEC 63000: 2018
Technical file at:
RUPES S.p.A. a socio unico
Via Marconi, 3/A - Loc. Vermezzo
20071 VERMEZZO CON ZELO (MI) - Italy
Vermezzo con Zelo (MI), 01/12/2021
S.p.A. a socio unico
THE PRESIDENT
G. Valentini
7