Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Control panel
Content displayed on the display
Displayed for 1 second after it is switched on.
-
Multifunctional display area
ODO: total mileage
DST: mileage of the current route (unit: mile, km)
TIME: start time
Error codes
-
Speed display area
AVG: medium speed
MAX: maximum speed
SPEED: current speed (Mp/h, km/h)
The motor sends the speed signal to the controller. The console calculates the actual speed
based on wheel diameter and signal data.
Assistance modes
Assistance indicator lights
Assistance indicator lights
Brake failure warning
Switch off
Headlight on
Cruising speed
Error codes
Error code
E06
E07
E08
E09
E10
E11
Parameters
P01: Brightness (level 1 is the darkest and level 3 the brightest).
P02: Mileage unit, 0: KM; 1: MILE
P03: Voltage level: 24 V, 36 V, 48 V, 60 V, 64 V; default 36 V.
P04: Latency time. 0 indicates no latency. Any other number indicates latency time. Range: 1-60
(minutes).
80
MOUNTAIN MILLOR
Meaning
Battery is running low
Electronic failure
Handlebar failure
Controller failure
Data reception failure
Data sending failure
P06: Wheel diameter (inches). Precision: 0.1. This parameter is related to the speed displayed
on the console.
Note: The unit used is kilometres. When changing from kilometres to miles, the speed shown
will be in miles. However, the speed limit will not be changed to miles.
Note: Programmes P09-P15 are only valid in communication status.
P09: Zero (and non-zero) start. 0 indicates zero start; 1 indicates other non-zero starts.
P11: Pedal fl uidity range: 1-24.
P12: Gears: 0-5.
P14: The limit value of the controller is set to 12 A by default. Range: 1-20A
P15: Controller voltage setting.
P16: ODO. To set the value to zero, press and hold the button for fi ve seconds.
P17: Cruising speed. A value of 0 means that it is not allowed to activate the cruising speed.
When activated, 1 will be displayed.
P18: Adjusting the size of the speed on the display (50%~150%).
P19: Assistance mode. If the number displayed in the assistance mode is 0, it means that
assistance is not activated. 1 means that assistance is activated.
P20:0:2 Protocol 1:5 S Protocol 2: Standby 3: Standby
Button operation
Press the
button to switch on the console. When it has been switched on, press
1.
the
button again to switch between ODO, DST, and TIME.
2.
Press and hold the
button to switch off the console. Press the
PAS (Pedal Assist System) will increase by one level. Press the
will decrease by one level.
3.
Press and hold the
button to switch the headlight on or off .
4.
If the bike is parked, when the display shows the speed display area, press, and hold
the
button to enter the start mode at standstill (6 km/h).
Press and hold the
and
buttons to go to the settings.
5.
6.
When you have selected a programme, press
7.
Press
and the value will increase by one level; press
by one level. When you have adjusted the programme settings, press the
to save the changes and move on to the next programme. Press and hold the
buttons again to save changes and exit the programmes.
8.
If no action has been done after 8 seconds, the changes will be saved automatically,
and the display will stop displaying the programmes.
Recommendations for gear changes
To improve the range of the electric bike, we recommend changing the gear ratio according to
the speed. A lower gear is best for low-speed off -roading and travelling. At higher speeds it is
best to choose a higher gear. Releasing the pressure on the pedals during shifting will allow
smooth assistance and better autonomy.
ENGLISH
button and the
button and the PAS
to modify the values.
and the value will decrease
button
and
81
MOUNTAIN MILLOR
Publicidad
