Set-Up Codes - Maytag MDE20PDAGW Instrucciones De Instalación

Secadora a gas o eléctrica comercial
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ELECTRONIC CONTROL SETUP INSTRUCTIONS
(PD & PN MODELS ONLY)
Control Set-up Procedures
IMPORTANT: Read all instructions before operating.
The fabric setting buttons along with the digital display are
used to set up the dryer controls. The display can contain
4 numbers and/or letters and a decimal point. These are used
to indicate the set-up codes and related code values available
for use in programming the appliance.
How to Use the Buttons to Program the Controls
1. The HEAVY DUTY button is used to adjust the values
associated with set-up code. Pressing the button will
change the value by increments. Rapid adjustment is
possible by holding down the button.
2. The NORMAL button will advance through the set-up
codes. Pressing the button will advance to the next
available set-up code. Holding down the NORMAL button
will automatically advance through the set-up codes at a
rate faster than 1 per second.
3. The DELICATES button is used to select or deselect options.
Start Operating Set-up
Single Load Models: Insert service door key, turn, and lift to
remove service door.
IMPORTANT: The console must not be opened unless power
is first removed from the dryer. To access connector AA1:
g Unplug dryer or disconnect power.
g Open console, disconnect plug on AA1, close console.
g Plug in dryer or reconnect power.
The dryer is now in the set-up mode.
NOTE: This dryer is preset at the factory and does not require
any programming. However, if you want to change the settings,
follow the "Set-Up Codes" guide to the right.
■ Units are pre-set at the factory for fixed cycle price with
top off.
22

Set-Up Codes

The NORMAL button will advance you from code to code.
The HEAVY DUTY button will change the code value.
The DELICATES button will select or deselect options.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
Code
Explanation
606
REGULAR CYCLE PRICE
606
Represents the number of quarters (coin 1) needed
to start the dryer; may adjust from 0–39 (See
VALUE OF COIN 1 b.05). Advance from 0–39 by
pressing the HEAVY DUTY button. Factory default
of 6 quarters = $1.50.
• Press the NORMAL button once to advance to next
code.
REGULAR DRY TIME
705
705
Represents the number of minutes per quarter (coin 1).
Factory default of 5 minutes per coin.
Example: 6 quarters x 5 minutes = 30 minutes.
By pressing the HEAVY DUTY button, value adjusts
from 1–75 minutes.
• Press the NORMAL button once to advance to
next code.
800
TYPE OF DRYER PRICING
800
Fixed Cycle with Top Off. For detailed description,
see "General User Information."
• Press the NORMAL button once to advance to
next code.
9 00
CYCLE COUNTER OPTION
This option is either NOT SELECTED "OFF" or
SELECTED "ON."
9 00
Not Selected "OFF."
9 0C
Selected "ON" and not able to be deselected.
• Press the DELICATES button 3 consecutive times
to select "ON." Once selected "ON" it cannot be
deselected.
• Press the NORMAL button once to advance to
next code.
If cycle counter (9 0C) is selected, the following
is true:
1 00
Cycles in HUNDREDS
2 00
Cycles in ONES
This is "VIEW ONLY" and cannot be cleared.
• Press the NORMAL button once to advance to next code.
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225

Publicidad

Tabla de contenido
loading

Tabla de contenido