Set-Up Codes - Maytag MDG25PN Instrucciones De Instalación

Start Operating Set-Up
PD Models: Insert service door key, turn, and lift to remove
■
service door.
PN Models: Remove the AA1 jumper from the control board
■
(see procedure below) or use the Service Access Code
below. Once the debit card reader is installed (according to
the reader manufacturer's instructions), the Set-Up mode
can be entered by inserting a manual set-up card (supplied
by the reader manufacturer) into the card slot. If manual
set-up card is not available, manual set-up mode cannot
be entered. However, Diagnostic mode can be entered
by removing connector AA1 on the circuit board.
IMPORTANT: The console must not be opened unless
power is first removed from the dryer. To access connector
AA1:
g Unplug dryer or disconnect power.
g Open console, disconnect plug on AA1, close console.
g Plug in dryer or reconnect power.
n PN Models Equipped with Programming Switch: Insert
access panel key and turn counterclockwise.
n PN Models with Gen. 2 Debit Card Reader: Once a Gen.
2 debit card reader is installed (according to the reader
manufacturer's instructions), the Set-Up mode can only
be entered by inserting a manual set-up card (supplied
by the reader manufacturer) into the card slot.
If manual set-up card is not available, only diagnostic mode
can be entered.
n Alternate method of entering Set-Up mode by entering
Service Access Code: This code can be entered to access
Set-Up mode without removing the console on dryers
just removed from the carton or not yet programmed. The
Service Access Code only functions on dryers set up for
0 vend price without any Special Pricing setup, and the
Coin/Debit Option must be set to "J._d". If the dryer is
not in Failure mode, the door must be opened to proceed.
Using only the 3 bottom buttons (numbered 1, 2, and 3 from
left to right):
1. Press 2 for longer than 2 seconds but less than
10 seconds.
2. Press 1 and 3 simultaneously for 2 seconds.
Display shows S 3.
3. Press 1 and 2 simultaneously. Display shows S 4.
4. Press 2 and 3 simultaneously. Display shows S 5.
5. Press 2.
6. Wait at least 2 seconds, but not more than 15 seconds,
then press in succession: 3, 2, 1, 3.
The dryer is now in the set-up mode.
NOTE: This dryer is preset at the factory and does not require
any programming. However, if you want to change the settings,
follow the "Set-Up Codes" guide below. PD models require a
payment system or OPL kit to be installed prior to operation.
n PD Models are pre-set at the factory for fixed cycle price
with top off.
n PN Models are pre-set for fixed cycle operation so they
can be run without payment.

Set-Up Codes

The PERM. PRESS button will advance you from code
■
to code.
The WHITE AND COLORS button will change the code
■
value.
The DELICATES button will select or deselect options.
■
PN MODELS: The set-up codes are the same as for the PD
models except where noted.
ELECTRONIC CONTROL SETUP INSTRUCTIONS
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
NOTE: The first line of each code indicates the factory default.
Code Explanation
6 06 REGULAR CYCLE PRICE
6 06 Represents the number of coins (coin 1) needed to
start the dryer; may adjust from 0–39. (See b.xx set up
for VALUE OF COIN 1.) Advance from 0–39 by pressing
the WHITES AND COLORS button. Factory default of
6 x coin 1.
PN MODELS ONLY: Factory default of 6 00, or 0 coins.
6 00
• Press the PERM. PRESS button once to advance
to next code.
7 05 REGULAR DRY TIME
7 05 PD MODELS: Represents the number of minutes
per coin (coin 1).
Factory default of 5 minutes per coin.
Example: 6 coins x 5 minutes = 30 minutes.
By pressing the WHITES AND COLORS button,
value adjusts from 1–99 minutes.
PN MODELS: Represents the cycle length for free
7 45
cycles. Example: "7 45" = 45 minutes.
• Press the PERM. PRESS button once to advance
to next code.
8 00 TYPE OF DRYER PRICING
8 00 Fixed Cycle with Top Off. For detailed description,
see "General User Information."
8 FC PN MODELS ONLY: Factory default of FC. Fixed
Cycle. For detailed description, see "General User
Information." Use the DELICATES button to change
this selection.
• Press the PERM. PRESS button once to advance
to next code.
CYCLE COUNTER OPTION
9 00
This option is either NOT SELECTED "OFF" or
SELECTED "ON."
9 00 Not Selected "OFF."
9 0C Selected "ON" and not able to be deselected.
• Press the DELICATES button 3 consecutive times
to select "ON." Once selected "ON," it cannot be
deselected.
• Press the PERM. PRESS button once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Cycles in HUNDREDS
2 00 Cycles in ONES
This is "VIEW ONLY" and cannot be cleared.
• Press the PERM. PRESS button once to advance
to next code.
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225
23