Explanation Of General View; General Power Tool Safety Warnings; Circular Saw Safety Warnings - Makita SP6000 Manual De Instrucciones

Ocultar thumbs Ver también para SP6000:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 40
ENGLISH (Original instructions)
1.
Clamping screw
2.
Blade lower limit stopper
3.
Quick stop button
4.
Clamping screws
5.
Tool base
6.
Positive stopper
7.
Lever
8.
Bevel angle shifting lever
9.
Base
10. Cutting line
11. Lock-off button
SPECIFICATIONS
Blade diameter
Max. cutting depth
No load speed (min
Overall length
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s). The lightest and heaviest combination, according to EPTA-
Procedure 01/2014, are shown in the table.
Intended use
The tool is specially intended for performing plunge cuts.
The tool is also intended for rip and cross cuts in wood. If
the tool is equipped with proper circular saw blade, the
tool can be used for aluminum board, plastic board, siding
board and metal wall panels.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety
warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
6

Explanation of general view

12. Switch trigger
13. Speed adjusting dial
14. Hex wrench
15. Locking lever
16. Shaft lock
17. Hex bolt
18. Outer flange
19. Saw blade
20. Inner flange
21. Vacuum cleaner
22. Dust port
Model
at 90°
at 45°
at 48°
-1
)
Net weight
Safety class
CIRCULAR SAW SAFETY
ENE067-2
WARNINGS
Cutting procedures
1.
DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
ENF002-2
are holding the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a
GEA010-2
stable platform. It is important to support the work
properly to minimise body exposure, blade binding, or
loss of control. (Fig. 1)
5. Hold the power tool by insulated gripping
surfaces, when performing an operation where the
cutting tool may contact hidden wiring or its own
cord. Contact with a "live" wire will also make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
6. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
23. Adjusting screws
24. Slide lever
25. Rip fence (Guide rule)
26. Rear edge of tool base
27. Fixed stop
28. Adjusting screw for 90°
29. Adjusting screw for 45°
30. Limit mark
31. Screwdriver
32. Brush holder cap
SP6000
165 mm
56 mm
40 mm
38 mm
2,200 - 6,400
341 mm
4.1 kg
/II
GEB144-2

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sp6000jsp1

Tabla de contenido