Eshift With Enviolo Automatic+ (Nuvinci Optimized); Eshift With The Kiox On-Board Computer - Bosch PowerPack 300 BBS245A Manual Del Operador

eShift with enviolo automatic+
(NuVinci optimized)
eShift with the Intuvia on-board computer
In the <± NuVinci Cadence> mode, you can use the – or +
button on the operating unit to increase or decrease the de-
sired cadence. If you hold down the – or + button, the ca-
dence will increase or decrease in increments of five. The
desired cadence is shown on the display.
In the <± NuVinci Gear> mode, you can use the – or + but-
ton on the operating unit to switch back and forth between
multiple defined transmission ratios. The engaged transmis-
sion ratio (gear) is shown on the display.
Intuvia eShift basic settings menu
You can choose from the following additional basic settings:
...
<Gear calibration →>: You can calibrate the continuously
variable transmission here. Confirm the calibration by press-
ing the bike light button. Then follow the instructions. In the
event of an error, it may also be necessary to perform calib-
ration when riding. In this case too, confirm the calibration
by pressing the bike light button and then follow the instruc-
tions on the display. This menu item is displayed only when
the on-board computer is in the holder.
...
<Gear vx.x.x.x>: Variable speed transmission software ver-
sion. This menu item is displayed only when the on-board
computer is in the holder. This menu item only appears in
conjunction with an electronic variable speed transmission.
English – 8​

eShift with the Kiox on-board computer

eShift with the Nyon on-board computer
With the NuVinci/enviolo gear shifting, the desired cadence
The optimum gear for each speed is automatically engaged
can be changed while riding using the operating unit.
via a predefined desired cadence. You can choose between
multiple gears in manual mode.
To do this, press the select button and use the right-hand
button to navigate to the <Cadence> option. Then adjust the
In the <Cadence Control> mode, you can use the – or + but-
value using the + or – button on the operating unit. Next time
ton on the operating unit to increase or decrease the desired
you open the <Settings> menu, the <Cadence> option will
cadence. If you hold down the – or + button, the cadence
immediately be displayed, as the last setting on your on-
will increase or decrease in increments of five. The desired
board computer will have been saved. Kiox does not support
cadence is shown on the display.
a manual switching mode.
Under <Calibration>, you can calibrate the continuously
variable transmission. Then follow the instructions on the
display.
In the event of an error, it may also be necessary to perform
calibration when riding. Confirm the calibration here too,
and follow the instructions on the display.
Bosch eBike Systems
The optimum gear for each speed is automatically engaged
via a predefined desired cadence. You can choose between
multiple gears in manual mode.
...
Intuvia eShift function displays
You can choose from the following additional functions in
the function display (combination of text display and value
display):
...
<± NuVinci Cadence>/<± NuVinci Gear>: Press and hold
the "i" button for longer than one second to access the Nu-
Vinci menu item from any menu item in the information
menu.
To switch from the <± NuVinci Cadence> mode to the
<± NuVinci Gear> mode, press and hold the "i" button for
one second.
To switch from the <± NuVinci Gear> mode to the
<± NuVinci Cadence> mode, briefly press the "i" button.
The default setting is <± NuVinci Cadence>.
English – 8​
Range Odometer
(1 s)
eShift with the Kiox on-board computer
With the NuVinci/enviolo gear shifting, the desired cadence
can be changed while riding using the operating unit.
To do this, press the select button and use the right-hand
... button to navigate to the <Cadence> option. Then adjust the
value using the + or – button on the operating unit. Next time
you open the <Settings> menu, the <Cadence> option will
immediately be displayed, as the last setting on your on-
board computer will have been saved. Kiox does not support
a manual switching mode.
Under <Calibration>, you can calibrate the continuously
In the <Gear Control> mode, you can use the – or + button
variable transmission. Then follow the instructions on the
on the operating unit to switch back and forth between mul-
display.
tiple defined transmission ratios. The engaged gear is shown
on the display.
In the event of an error, it may also be necessary to perform
calibration when riding. Confirm the calibration here too,
Under <Gear calibration>, you can calibrate the continu-
and follow the instructions on the display.
ously variable transmission. Then follow the instructions on
the display.
In the event of an error, it may also be necessary to perform
calibration when riding. Confirm the calibration here too,
and follow the instructions on the display.
English – ​ 7
EN-97
NuVinci Cadence
(1 s)
NuVinci Gear
0 275 007 XES | (06.02.2019)