Declaration Of Conformity; Before Initial Commissioning - Bosch PowerPack 300 BBS245A Manual Del Operador

English – 2​
Technical data
On-board computer
Product code
Max. charging current of USB
port A)
USB port charging voltage
USB charging cable B)
Operating temperature
Charging temperature
Storage temperature
Internal lithium-ion battery
Protection rating C)
Weight, approx.
Bluetooth® Low Energy
– Frequency
– Transmission power
A) At an ambient temperature of <25 °C
B) Not included as part of standard delivery
C) When the USB cover is closed

Declaration of Conformity

Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the Kiox radio communication unit complies with Dir-
ective 2014/53/EU. The full text of the EU Declaration of
Conformity can be accessed at the following Internet ad-
dress: https://www.ebike-connect.com/conformity
Fitting
Fitting and removing the on-board computer
(see figure A)
Fit the lower part of the Kiox into the holder (5) first and tilt
it forward gently until you can feel that the on-board com-
puter is firmly fixed in the magnetic holder.
To remove the on-board computer, hold it by the top end
and pull it towards you until it disengages from the magnetic
holder.
Remove the on-board computer when you park the
u
eBike.
The on-board computer can be secured in place to prevent it
from being removed from the holder. To do this, loosen the
headset screw (16) until the Kiox holder can be swivelled
sideways. Put the on-board computer in the holder. Screw
the locking screw (M3 thread, 6 mm long) from below into
the thread provided in the on-board computer (using a
longer screw may damage the on-board computer). Swivel
the holder back into place and tighten the headset screw in
accordance with the manufacturer's specifications.
1 270 020 XBK | (12.03.2019)
Kiox
BUI330
mA 1000
V 5
1 270 016 360
°C −5 to +40
°C 0 to +40
°C −10 to +50
V 3.7
mAh 230
IP x7 (dustproof,
watertight)
g 60
MHz 2400–2480
mW <10
Operation

Before initial commissioning

The Kiox is supplied with a partially charged battery. Before
using it for the first time, this battery must be charged for at
least one hour via the USB port (see "Power supply of the on-
board computer", page English – 3) or via the eBike sys-
tem.
The control unit should be attached such that the buttons
are almost perpendicular to the handlebars.
When using the on-board computer for the first time, the lan-
guage selection page is displayed initially. You can then
choose to have essential functions and indications explained
via the <Intro to Kiox> menu item. The menu item can also
be called up at a later time via <Settings> → <Informa-
tion>.
Selecting system settings
Fit the on-board computer in the holder and proceed as fol-
lows with the bicycle stationary:
Go to the status page (use the < button (10) on the control
unit to get to the first display) and call up the <Settings>
with the select button.
You can use the – (11) and + (12) buttons to select the set-
ting you want. You can open the settings, as well as any addi-
tional submenus, using the select button (9). You can use
the < button (10) to go back to the previous menu from any
settings menu.
The following settings can be changed in the <Sys set-
tings>:
– <Brightness>
– <Time>
– <Date [DD.Mon.YYYY]>
– <Time zone>
– <24h form (24h time format)>
– <Brgh backg. (Bright background)>
– <Imp. units (Imperial units)>
– <Language>
– <Factory reset>
Starting up the eBike system
Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged eBike battery is inserted (see oper-
ating instructions for the battery).
– The on-board computer is properly fitted to the holder.
Switching the eBike system on/off
The following options are available for switching on the
eBike system:
– Once the on-board computer and the eBike battery are
fitted, briefly press the on/off button (4) on the on-board
computer.
EN-49
Bosch eBike Systems