Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
23) PTT
Transmission key, press to transmit a message, "TX" is displayed and release
to listen to an incoming communication.
A) DC-POWER TERMINAL (13,2 V)
B) ANTENNA CONNECTOR (SO-239)
C) EXTERNAL SPEAKER JACK (8 Ω, Ø 3,5 mm)
D) JACK FOR OPTIONAL PA (Public Address) (Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MIKE (Ø 2.5 mm)
F) JACK FOR CW DEVICE (Ø 3.5 mm)
G) USB DATA (PC setting in option)
C) MENU FUNCTIONS
Press the MENU key (4) for 2 seconds to
"FUNC" appears on the LCD.
Use s/t keys (10) to
select
the desired function.
Use rotary PUSH knob (6) to
set
Press any key except PUSH knob (6) or wait for 5 seconds to
"FUNC" disappears from the LCD.
1) ROGER BEEP FREQUENCY
Set
the FREQUENCY of the ROGER BEEP.
At [
] menu, rotate PUSH knob (6) to
Frequency range:
Hz ~ 3
Hz, stepping frequency:
300
000
Press PUSH knob (6) to
change
2) ROGER BEEP TIME
Set
the TIME (ms) of the ROGER BEEP.
At [
] menu, rotate PUSH knob (6) to
Time range
~ 1
ms, time stepping:
50
000
(6) to
change
the step.
3) CW FREQUENCY
Set
the FREQUENCY of the CW.
] menu, rotate PUSH knob (6) to
At [
Frequency range:
Hz ~ 3
Hz, stepping frequency:
300
000
Press PUSH knob (6) to change the step.
4) CALL FREQUENCY
Set
the FREQUENCY of the CALL tone.
enter
in the menu function setting.
the function.
store
set
the Frequency.
Hz, default:1
10
the step.
set
the delay Time.
ms. Press PUSH knob
ms, default:
50
500
set
the Frequency.
Hz, default:1
10
At [
] menu, rotate PUSH knob (6) to
Frequency range:
Press PUSH knob (6) to change the stepping.
5) MONITOR GAIN VOLUME
Set
the OUTPUT VOLUME LEVEL of the microphone in your own speaker.
At [
] menu, rotate PUSH knob (6) to
There are 32 levels. "OFF"
6) TOT (Time Out Timer)
Set
the TOT. If the PTT pedal (23) is pressed for more than "TOT" time, the
transmission ends.
At [
] menu, rotate PUSH knob (6) to
tion. Time range 3
7) SWR PROTECTION
Enable/disable
the SWR PROTECTION.
At [
] menu, rotate PUSH knob (6) to
protection. Default: "
8) SWR PROTECTION SETTING
and exit.
Set
the SWR LEVEL PROTECTION.
At [
] menu, rotate PUSH knob (6) to
Level range:
~ 2
12
the step. The SWR level is useful only in the SWR protection function is active.
9) VOLTAGE PROTECTION
Hz.
Enable/disable
VOLTAGE PROTECTION.
050
At [
] menu, rotate PUSH knob (6) to
the protection. Default: "
10) VOLTAGE PROTECTION HIGH
Set
the HIGHER LIMIT of VOLTAGE PROTECTION.
At [
] menu, rotate PUSH knob (6) to
Voltage range:
90U
to change the step. The HIGH limit is useful only if the VOLTAGE protection
function is active.
11) VOLTAGE PROTECTION LOW
Set
the LOWER LIMIT of VOLTAGE PROTECTION.
Hz.
050
At [
] menu, rotate PUSH knob (6) to
Voltage range:
90U
to change the step. The LOW limit is useful only if the VOLTAGE protection
function is active.
11
set
the Frequency.
Hz ~ 3
Hz, stepping frequency:
300
000
set
the Monitor volume level.
disable
the function.
set
the TOT, "
~ 60
s, time stepping: 3
s, default: 18
0
0
0
enable
"
".
set
the protection Level.
, stepping:
, default: 2
. Press PUSH knob (6) to change
00
1
00
enable
".
set
the High limit.
~ 1
V, stepping:
, default: 1
70U
01U
set
the Low limit.
~ 1
V, stepping:
, default:
70U
01U
90U
Hz, default:1
Hz.
10
050
"
disable
the func-
s.
0
" or
disable
"
" the
"
" or
disable
"
"
. Press PUSH knob (6)
70U
. Press PUSH knob (6)
Publicidad
Tabla de contenido
