Tool Application Guide - Husqvarna RG 2112 Manual Del Operador

Tool Attachment
To Machine
Grinding Stones Accessory Disk and
Wooden Wedges
(See FIG. 14)
(Section 4.1)
See Current
Product Catalog
for Part Numbers
of these Items.
Diamond Accessory Disk and
Segment Blocks Wooden Wedges
(See FIG. 15) (Section 4.2)
See Current
Product Catalog
for Part Numbers
of these Items.
Tungsten Accessory Disk and
Carbide Blocks Wooden Wedges
(FIG. 16, FIG. 17, (Section 4.3)
FIG. 18)
Scarifier Wheels Accessory Disk and
Wooden Wedges
(FIG. 27, FIG. 28)
(Section 4.4)
See Current
Product Catalog
for Part Numbers
of these Items.
Wire Brushes Accessory Disk and
Wooden Wedges
(FIG. 26) (Section 4.5)
Diamond Disks Adapter Plates
(FIG. 25) (Section 4.6)
See Current
Product Catalog
for Part Numbers
of these Items
Scrubbing Pads Tool Holder Pad
(FIG. 19)
(Section 4.7)

Tool Application Guide

Light Grinding of Rough Areas
Available In Different Silicon Carbide "Grit" Sizes, such as:
TSC-10 Coarse Grit: Maximum material removal, General grinding & removal of
trowel marks, high spots, and rough sections of concrete. Life 4-10 hours.
TCS-24 Medium Grit: Lower material removal rate, Finer finish grinding of concrete,
and rough grinding of Terrazzo and other stone type. Life 6 - 10 hours.
TCS-80 Fine Grit: Still lower material removal rates. For polishing of concrete
and medium grinding on Terrazzo and stone type floors. Life 8 - 20 hours.
(The larger the number, the finer the grain structure, and the smoother the surface
material finish, and the longer the grinding stone life)
Remove High Spots, Trowel & Rain Marks, Paints, Sealers & Mastics, Uneven
Joints, Aggressive Grinding of Large Rough Areas, Removal of epoxies,
paints and many thin film coatings, or Final Preparation for new coating.
Available In Different "Grit" Sizes:
GB-10 General Purpose,GB-20 Abrasive Materials
GB-30 Epoxy & Non-Abrasive Materials.
Removal Rates: Up to five (5) times the material removal rate
Life: Up to 15 times the life of Grinding Stones.
Removal of Thick Paint Coatings, Not Recommended for Thin (< 5 mil)
Films of Materials. Not Recommended for adhesive, rubber deposits
and mastics which have a tendency to extrude or smear rather than
"shear" loose from the floor surface - however water or a water / sand
mixture can be added on the surface to reduce this problem.
Remove Fiberglass, Ice, Oil-Dry, Foam-Fill Packing Material & Floor Buildups.
Star Wheel: Hardened Carbon Steel material. For removal of thin coatings
and encrusted accumulations of material. Cleaning concrete of asphalt surfaces.
Removing thick build-up of grease, paint, and some resins. Light scarifying before
application of coatings or sealer. Creates a swept, or "broomed" type of finish.
Beam Wheel: Medium duty, for concrete and asphalt scarifying.
De-scaling steel decks. Removing thick material build-up of grease, paint,
and some resins. Twice the life, near the same cost as a star wheel.
Tungsten Carbide Wheel: Heavy Duty asphalt or concrete scarifying,
or de-scaling of steel decks. 10 times the life of a star wheel.
Notes: Should be rotated end for end in accessory disk every hour
to avoid the wire taking a set (flat wire will bend in one direction).
External weight added to machine will NOT normally increase
production rates, but only accelerate the wire brush wear rates.
Remove High Spots, Trowel & Rain Marks, Paints, Sealers & Mastics,
Uneven Joints, Aggressive Grinding of Large Rough Areas, Removal of epoxies,
paints and many thin film coatings, or Final Preparation for new coating.
Available In Different "Grit" Sizes and 10 or 20 Diamond Segments (per disk):
TDGH-10C for Cured Concrete (10 Segments)
TDGH-20C for Cured Concrete (20 Segments)
TDGH-20A for Asphalt or Abrasive Surfaces (20 Segments)
Removal Rates: Up to five (5) times the material removal rate of Grinding Stones.
Life: Up to 15 times the life of Grinding Stones.
Remove mildew, rust, or discoloration from concrete, clean concrete forms, strip scale
and rust from steel plate surfaces, remove fins or marks on underlayment materials.
Task
of Coarse Grinding Stones.
Lightly Texture Surface.
Light Scarifying & cleaning.
22
Surface
Material
Concrete
Terrazzo
Other Stone
Types
Concrete
Terrazzo
Other Stone
Types
Concrete,
Epoxy,
Coatings, &
Mastics
Concrete
and Tile
Concrete,
Asphalt,
Steel, and
Tile
Concrete
Terrazzo
Other Stone
Types
Concrete,
Steel