Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
16
PRO 35III ELECTRIC SAWS
The Pro 35III is available in several 20HP electric
versions. It is available in 4 different voltages with three
(3) different motors.
appropriate plugs, connectors, wiring, motor starter,
overload heaters and an in dash current load meter. The
electric saw is operated exactly like a gas saw after it is con-
nected to the power source. The key must be turned to the
Start position and will engage the motor starter. Turn the
key off, the motor will stop. The emergency stop switch and
water safety switch will also stop the motor.
Operate the electric saw at a speed where the current load
meter does not exceed 100% of full load current. Exceed-
ing 100% of the full load amperage will result in the current
overload heaters to overheat and shut off the electric motor.
After allowing the overload to cool off, (approx. 5 minutes),
press the RESET button on the front of the electrical enclosure
box. Turn the key to the start position to engage the motor
starter.
See page 15 for further details.
WARNINGS!!!
DO
turn the "ON/OFF" switch to the "OFF" position prior
to connecting the machine to the power source.
DO
make sure electric powered machines are plugged
into a properly grounded circuit.
DO
make sure power cords are the proper size and in
good condition.
DO
follow all electrical codes in your area.
DO
use correct voltage and proper extension cords.
Never carry tool by cord or yank it to disconnect it
from receptacle. Keep cord away from heat, oil and
sharp edges.
DO
disconnect tools from power source when not
in use, before servicing and when changing
accessories.
DO
carefully maintain and clean for better and safer
performance. Follow instructions for changing
accessories. Inspect tool cords periodically and,
if damaged, have repaired by authorized service
facility.
DO NOT
lay power cords in or near the water.
DO NOT
leave this machine unatteded with the motor
running.
DO NOT
replace the motor with any motor that does not
have a special grounding connection.
30
It comes completely wired with
17
ACCESSORIES
BLADE GUARD CONVERSION KITS:
Use the proper size blade guard for the particular diamond
blade size being operated. See Charts on pages 49 - 51 for
blade guards that are available.
WEIGHT KIT: (Pro 65 III or Pro 40 III)
A rear mounted Weight Kit is available. It is standard
equipment for units shipped with 48" blade guards. It can
be purchased as an accessory for units with smaller blade
guard sizes.
ACCESSORIES AND KITS
Item
Part No.
Deluxe Light Kit
167656
Tie Down Kit
167190
Upright Muffler
163715
Upright Quiet
Muffler
163801
Upright Quiet
Muffler
167438
48" Conversion
176821
Blade Guards:
18" Slip-on
176635
18" Bolt-on
174273
26" Slip-on
176645
26" Bolt-on
167475
30" Slip-on
166911
30" Bolt-on
167676
36" Slip-on
166931
36" Bolt-on
174275
48" Bolt-on
166932
Water Pump Kit
167554
Blade Stack Kit
(Std. Shaft) (4.50")
176292
Blade Stack Kit,
QDS Flanges:
5.00" Dia
177327
6.00" Dia
163480
Side Plunge Kit
163944
Notes:
1.
If A Box Is NOT CHECKED, That Item IS NOT AVAILABLE For
The Saw Model Shown.
2.
New Saw Models (Pro 35 III, Pro 40 III, Pro 65 III) Have Some
Of These Items Installed As Standard
35III
40III
65III
65III
Prem. Basic
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Elec
Only
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Publicidad
Tabla de contenido
