Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
•
Gas Models: Push in the Engine Choke (1Q).
•
Put the Control Lever (1S) into gear, push the lever
forward for Forward saw movement, or to the rear
for Reverse saw movement. The further you push the
lever the faster the speed.
DO NOT attempt to start the saw while it is
p a r k e d o n a g r a d e ( o r h i l l ) , u n l e s s t h e
Parking Brake Switch (1N) is in the AUTO
position.
3
TRANSPORT (BLADE REMOVED)
(See Fig. 1, 2, and 3)
S e t Pa r k i n g B r a k e S w i t c h ( 1 N ) t o a u t o
position. Remove diamond blade (2E) before
transport.
When moving the saw up and down ramps, with the
engine on, use extreme caution.
•
To go DOWN a ramp, drive the saw FORWARD slowly.
•
To go UP a ramp, back the saw in REVERSE slowly.
WARNING! DO NOT roll the saw down a ramp while
the control lever is in the NEUTRAL (1V) position.
Lifting The Saw. The saw can only be lifted by the
factory installed Lifting Bail (3B).
To Transport By Vehicle:
•
Set the Engine Start Switch (1I) in the OFF position.
•
Set Speed Control Lever (1S) in the NEUTRAL (1V) posi-
tion.
•
Push Handle Bars (1B) inward and tighten Knobs (1A).
Block the saw in place or secure it into place to pre-
vent movement during transport.
4
CHECK BEFORE STARTING
Take into account the working conditions from the
health and safety point of view.
•
Fuel: Check the engine maintenance manual.
∗
Gas Models: Unleaded gasoline is recommended.
∗
Diesel Models: #2 Diesel fuel is recommended.
•
Check that the engine oil level is correct. Because
the engine often operates at an angle, check the oil
level (with engine horizontal) frequently to ensure that
24
the oil level never falls below the lower mark on the
dipstick. 10W30 oil is recommended.
•
For start up, refer to the engine manual.
5 FITTING THE BLADE
(See Fig. 1 and 2)
Always set the Engine Start Switch (1l) to the OFF
position before mounting the blade.
•
Set the Engine Start Switch (1I) to the OFF position.
•
Raise the machine to a high position [by pressing the Red
Button (1R) on the Control Lever (1S) upward].
•
Loosen the bolt on the Blade Guard Latch (2G).
•
Raise the front half of the Blade Guard (2H).
•
Unscrew the Blade Shaft Bolt (2A). Remove Outer Flange
(2B).
•
Fit Diamond Blade (2E) to Outer Flange Arbor (2C).
•
Install Outer Flange (2B) into the Blade Shaft (2I)
making sure that the Locking Pin (2D) passes through the
Diamond Blade (2E) and into the Inner Flange (2F).
Note the direction of rotation of the blade.
The direction of rotation is shown by an
arrow on both the Diamond Blade (2E) and
the Blade Guard (2H). Make sure that the
contact surfaces on the Diamond Blade (2E),
Inner & Outer Flanges (2B & 2F) and Blade
Arbor (2C) are clean.
•
Rotate Outer Flange (2B) and Diamond Blade (2E) in
the opposite direction of blade rotation to remove
backlash.
•
Install and tighten Blade Shaft Bolt (2A) using the Blade
Shaft Wrench while firmly holding the Diamond Blade
(2E).
•
Lower front half of Blade Guard (2H) and tighten the Bolt
(2G) on the Blade Guard Latch (2G).
The Blade Shaft Bolt (2A) on the Right Hand side has
Left Hand threads. The Blade Shaft Bolt (2A) on the
Left Hand side has Right Hand threads.
Slip on blade guards are provided with a safety
latch which engages the support spade and a bolt
to retain the rear of the guard.
Do not operate this saw without the latch
engaged and the bolt installed. Inspect blade
guards and latches frequently. DO NOT USE IF
DAMAGED.
To Remove A SLIP-ON GUARD:
Publicidad
Tabla de contenido
