Instructions: 1. Use; Moving The Machine - Husqvarna FS 3500 Manual Del Operador

MANDATORY
WARNING
These signs will give
advice for your safety
Before leaving our factory every machine is thor-
oughly tested.
Follow our instructions strictly and your machine will give you
long service in normal operating conditions.
1 USE
Use: Wet sawing of old and new concrete and asphalt.
Tools: Diamond blades — water cooled, Ø: 12",14", 18", 20",
24", 26", 30", 36", 42" and 48" with Arbor Ø - 1"
(For information, contact your Target supplier)
Depths of Cut (Maximum):
12 "
MODEL
35 III
3¾
40 III
3½
65 III
3½
Side Plunge
---
26 "
MODEL
35 III
10¾
40 III
10½
65 III
10½
Side Plunge
n/a
*Electric Only (12-1/2")
Before starting up the machine, make sure you read
this entire manual and are familiar with the opera-
tion of this machine.
The working area must be completely clear, well lit
and all safety hazards removed.
INDICATION
INFORMATION
INSTRUCTION
PROHIBITION
Blade Size
14 " 18 " 20 "
4¾ 6¾ 7¾
4½ 6½ 7½
4½ 6½ 7½
" "
--- 2 3
Blade Size
30 " 36 " 42 "
n/a n/a
*
n/a n/a
12½
12 15 17
n/a n/a n/a
The operator must wear
p r o t e c t i v e c l o t h i n g
appropriate to the work he is
doing.
A ny p e r s o n s n o t i nvo l ve d i n t h e wo r k
should leave the area.
Use only blades marked with a maximum
operating speed greater than the blade shaft
speed.
2

MOVING THE MACHINE

Set The Handles To The Desired Length:
•
Loosen Knob (1A), pull the Handle Bar (1B) in or out to
desired length, then tighten the Knob (1A).
Moving The Saw With The Engine Off:
•
Turn Engine Start Switch to the "RUN" position.
•
Raise the saw by pressing the top side of the Red
Button (1R) on the Speed Control Lever (1S) until the
Diamond Blade (2E) (if installed) clears the pavement
surface.
•
Put the Speed Control Lever (1S) into the Neutral (1V)
position.
•
Release the Parking Brake by turning the Parking Brake
Switch (1N) to the OFF position.
•
The saw can now be moved by standing behind it and
pushing [while holding the Handle Bars (1B)].
DO NOT attempt to push the saw while it is
24 "
parked on a grade (or hill). The saw opera-
9¾
tor could lose control of the saw and cause
9½
injury to himself or other person(s) in the area. In an emer-
9½
gency push the Emergency Stop Switch (1T). This will engage
n/a
the Parking Brake.
Moving The Saw With Engine On:
48 "
•
Raise the saw by pressing the top side of the Red
n/a
Button (1R) on Speed Control Lever (1S) until
n/a
Diamond Blade (2E) (if installed) clears the pavement
20
surface.
n/a
•
Set the Parking Brake Switch (1N) to the AUTO
position.
•
Press the Water Safety Switch (1E) button. This will reset
the Water Safety Switch, if the water supply has been
interrupted.
•
Speed Control Lever (1S) must be in the Neutral (1V) posi-
tion to start the saw. The engine WILL NOT start unless the
Speed Control Lever (1S) is in the Neutral (1V) position.
•
Gas Models: Pull out the Engine Throttle (1P) and Choke
(1Q).
•
Diesel Models: Pull Throttle(1P) out halfway.
•
Turn the Engine Start Switch (1I) to the start position until
the engine starts, then release the switch. It will return to
RUN position. If the engine does not start, repeat these
steps.
(See Fig. 1 and 2)
23