Surtek TRHP2 Manual De Usuario Y Garantía página 7

Fig.5
Test of hand pallet truck
After the truck is assembled, try to rock the
hand grip and operate different positions of
control handle knob (10) to examine the lift-
ing, free position and dropping and check that
whether the different positions are normal or
not. See figure 5.
The screw 9 in figure 4 is used to adjust the truck
situation. When the truck body drops immedi-
ately after it's lifted, turn the screw (9) a little
counter-clockwise.
And then try to operate the truck again until
truck body can lift normally. If the truck body
can't drop after it's lifted, turn the screw clock-
wise. And then try to operate truck again until
the truck body can drop normally. The external
hex nut (8) in the screw (9) plays part as the lock-
ing function in the truck. So you should undo
the external hexagon nut (10) before adjust-
ment and screw down the nut (8) after you fin-
ish the adjustment.
OPERATION INSTRUCTIONS
Before operation
the hand pallet truck
please make sure that
whether the cargo
weight exceeds the
rated load or not.
The correct cargo load-
ing type should be as
shown in figure 6.
• See figure 5, when hand knob (10) is placed on
the lift position, the truck will be in a state of
lift. At this time, if you rock the hand grip, the
truck will be lifted.
• When hand knob 10 is placed on the free po-
sition, the truck will travel. At this time, if you
rock the hand grip, the truck will neither lift nor
drop. Then, you can use the truck to move the
cargo.
• When the hand knob 10 is placed on
the drop position, truck forks will drop. At this
time, the truck forks will drop automatically.
- When the hand knob 12 is placed below, the
truck will be in a state of free walking.
- When the hand knob 12 is placed above, the
7
Drop position
Free position
Lift position
of
Fig.6
truck will be in a state of brake.
- Hand knob 11 is used for release brake.
Points for attention and safety norms
· The operators must put on the work clothes,
safety shoes and gloves during the operation of
the hand pallet truck.
· When the hand pallet trucks are transported
by truck, the hand pallet trucks should be locked
in order to prevent the trucks from moving.
· When the hand pallet truck is used for the mo-
tor vehicle, the truck must be moved slowly to
ensure safety.
· The wheels, bearings and bushings of the truck
are wearing parts. Please change them accord-
ing to situation.
· Do not park the truck on the slope or in emer-
gency passages.
· When the hand pallet truck is used on the
slope, the operator should operate the pallet
truck carefully to ensure the operator on top of
the slope.
· When the hand pallet truck is not in use, the
forks should be lowered to the lowest position.
· It is forbidden to stop the truck on the slope.
· Do not park the truck at places where will
block the traffic or is inconvenient for work.
· Do not use the truck in rainy environment.
· It is forbidden for the operator to sit or stand
on the hand pallet truck to operate the truck.
· It is forbidden to make turns on the slope.
· Do not pile the cargo too high in order to pre-
vent the goods from falling down or overturn-
ing of the truck.
· Do not use the hand pallet truck to carry peo-
ple.
· Untrained personnel are not allowed to stand
around the operation area in order to avoid in-
jury caused by sudden malfunction.
· Before the hand pallet truck is pushed into the
elevator, the operator shall make sure that the
elevator can bear the total load of hand pallet
truck and cargo as well as the total weight of
the operator and other personnel in the eleva-
tor. When entering the elevator, people should
let the load enter first but not operator. When
the load or hand pallet truck enters or leaves
the elevator, other personnel should not stay in
the elevator.
· The hand pallet truck should be stored in dry
and ventilated environment.
· When the cargo weight exceeds 2500kg, please
operate the truck by two person together for
labor-saving.