Functions Turning On The Unit; Functions With Ptt Pedal - PRESIDENT ANDY Manual Del Usuario

C) FUNCTIONS TURNING ON THE UNIT
5 more functions are available. Turn off the unit. Turn on the radio
while pressing one or two keys to set the function ON. Repeat this
action to set the function OFF.
1) ROGER BEEP
(t key on the unit or UP knob on microphone)
The ROGER BEEP sounds when the PTT switch (8) of the microphone
is released in order to let your correspondent speak. Historically as
CB is a "simplex" communication mode, it is not possible to speak
and listen at the same time (as it is the case with a telephone).
Once the conversation was over, he said "Roger" in order to pre-
vent his correspondent that it was his turn to talk. The word "Roger"
has been replaced by a significant beep. That is where the name
"Roger beep" comes from.
Use the following procedure to activated or deactivated the ROGER
BEEP function:
- Turn on the power while pressing the s key (2a) or UP knob (9) to
enable (rb on) or disable (rb oF) the ROGER BEEP function.
- When function is activated, " " appears on the display.
Note: The Roger beep also sounds in the loudspeaker if the KEY
BEEP function is active. If the KEY BEEP function is not active, only
the correspondent can hear the ROGER BEEP.
In PA mode the function is not allowed.
2) KEY BEEP
(t key on the unit or DN knob on microphone)
Some operations such as changing channels, pressure on keys etc.
are confirmed by a beep tone. This beep tone can be activated
or deactivated as follows:
- Turn on the power while pressing the t key (2b) or the DN knob (2)
to enable (BP on) or disable (bP oF) the KEY BEEP function.
- When function is activated, "BP" appears on the display.
3) F - FREQUENCY BAND SELECTION
(Configuration: EU; PL; d; EC; U; In)
The frequency bands have to be chosen according to the country
of use. Don't use any other configuration. Some countries need a
(F key)
user's licence.
See table page 54.
Proceeding:
- Turn on the power while pressing the F key (5).
The letter corresponding to the current configuration is blinking.
- In order to change the configuration, use the s/t keys (2) or the
UP/DN knobs (9) on the microphone or on the unit.
- When the configuration is selected, press the F key (5) 1 second.
The letter corresponding to the configuration are continuously
displayed and a confirmation tone beep sounds.
- At this point, confirm the selection by switching off the transceiver
and then switching it on again.
See the configurations / frequency bands table at pages 49 to 53.
4) TOT (Time Out Timer)
(MODE key)
If the transmission key is longer than 5 minutes, CHANNEL and ac-
tivated or deactivated
The time-out tone will sound until the PTT pedal (8) is released.
The TOT function can be activated or deactivated as follows:
- Turn on the power while pressing the MODE key (6) to enable
(t on) or disable (t oF) the TOT function.
5) COLOR
(EMG + MODE keys)
Use the following to alternate between the 3 colors:
- Turn on the power while pressing the EMG (5) and MODE (6) keys.
Current color blinks, (orange),
- Use the s/t keys (2) or UP/DN keys (9) to change the color.
- When the color is set, long press the F key (5). Beep sounds, the
characters of the color are displayed during 1 second.
D) FUNCTIONS WITH PTT PEDAL
3 more functions are available. To activated the function press
and hold the PTT pedal (8) and press the function key. Repeat this
process to deactivate the function.
32
start blinking, the transmission ends.
(green) or (bleu).