Setting The Cutting Height - Tramontina CE30M Manual De Uso

be released. To turn the mower off, let go of the lever [Fig. 20, Pag. 09].
Switch the engine on according to previous instructions and keep your feet away from the blade. Start the
engine with the cutting blade free. Never start the mower directly on tall grass.
After switching the engine off, the blade will stop turning in less than 3 seconds. This procedure may cause some noise
or a slight vibration, which is considered normal.
Keep hands and feet away from cutting blade.
Power Cord Gauge
MOTOR
127 V
850 W
2 x 1,5 mm²
1.100 W
2 x 2,5 mm²
1.300 W
2 x 2,5 mm²
1.800 W
2 x 2,5 mm²
2.500 W
2 x 4,0 mm²
The use of unauthorized cords may damage the engine and is not covered by the warranty.

Setting the Cutting Height

Models CE30M, CE30P, CE30P2, CE35M and CE35P
The settings are on the chassis of the lawn mower. To set the cutting height move the wheel height to one of the
3 adjustment positions. Try to set the same setting position for the height of both the front and rear wheels of the
lawn mower [Fig. 21, Pag. 09].
Models CE40M, CE40P and CE45M
The adjusting devices are located next to the lawn mower wheels. To adjust the cutting height it is enough to
move the adjusting rod pushing it out of the chassis in order to release it from the adjusting plate [Fig. 22, Pag.
10]. Try to set the same setting position for the height of both the front and rear wheels of the lawn mower.
Model CE40P has 4 cutting height positions: 25 mm - 40 mm - 55 mm - 70 mm.
Models CE40M and CE45M have 5 cutting height positions: 20 mm - 32 mm - 45 mm - 58 mm - 72 mm.
Some warnings are important when choosing the cutting height:
In order to make a low cut, the land must be flat, without undulations or holes otherwise the blade can touch the
ground impairing the engine output and damaging the lawn.
In very tall grass, first make a previous cut with the cutter adjusted to high level and then another cut with the
final desired cut. This will make the task easier and will not overload the motor.
Excess loading will cause an brisk fall in revolutions and engine overheating, which will reduce its useful
life or cause burnout and loss of warranty.
Before performing any kind of maintenance work, turn the engine off and unplug the equipment.
Ensure that all the screws and nuts are always well tightened by constantly checking if the equipment is ready for use.
If the power cord is damaged, it should be replaced by the manufacturer, an authorized dealer or a qualified person
to reduce risk of injury.
Instructions for waste disposal
Improper disposal of solid waste can cause serious damage to the environment, including soil and water contamination.
20 m
220 V 127 V
2 x 1,5 mm² 2 x 2,5 mm²
2 x 1,5 mm² 2 x 2,5 mm²
2 x 1,5 mm² 2 x 2,5 mm²
2 x 2,5 mm² 2 x 4,0 mm²
2 x 2,5 mm² 2 x 6,0 mm²
MAINTENANCE
30 m
220 V 127 V
2 x 1,5 mm² 2 x 2,5 mm²
2 x 1,5 mm² 2 x 4,0 mm²
2 x 1,5 mm² 2 x 4,0 mm²
2 x 2,5 mm² 2 x 6,0 mm²
2 x 2,5 mm² 2 x 8,0 mm²
40 m 50 m
220 V 127 V
2 x 1,5 mm² 2 x 4,0 mm²
2 x 1,5 mm² 2 x 6,0 mm²
2 x 1,5 mm² 2 x 6,0 mm²
2 x 2,5 mm² 2 x 6,0 mm²
2 x 2,5 mm² 2 x 8,0 mm²
220 V
2 x 1,5 mm²
2 x 1,5 mm²
2 x 1,5 mm²
2 x 2,5 mm²
2 x 2,5 mm²
20