Safety Notes - Monacor security TFT-1700COL Manual De Instrucciones

Please unfold page 3. Then you can always see the
operating elements and connections described.
1 Operating Elements (Front) and
Connections (Rear)
1 Power LED: red = stand-by
green = monitor switched on
2 Button MENU for calling and exiting the on-screen
menu
3 Arrow keys
function when the on-screen menu is not called:
button for automatic picture adjustment with
PC operation
button for switching between the signal
sources at the BNC input jacks VIDEO 1 (10)
and VIDEO 2 (18)
function with the on-screen menu called:
buttons "Down"
on-screen menu and to reduce or to increase
values for operating parameters
4 Button ENTER to activate menu pages and menu
items selected in the on-screen menu and to con-
firm some menu adjustments
5 Button BACK to go back to the respectively next
higher menu level in the on-screen menu
6 Button to switch on the monitor or to switch to
stand-by
7 Jack for the power supply (12 V ) via the supplied
power supply unit
8 Audio input AUDIO 1 (phono, stereo) for connection
to the audio output of the signal source connected
to the input VIDEO 1 (10) or S-VIDEO (12)
9 Audio output AUDIO 1 (phono, stereo) to pass on
the fed-through signal of the input AUDIO 1 (8) to
another unit
10 Video input VIDEO 1 (BNC) for connection of a sig-
nal source which supplies a composite signal
11 Video output VIDEO 1 (BNC) to pass on the fed-
through signal of the input VIDEO 1 (10) to another
unit
12 Video input S-VIDEO (mini DIN, 4-pole) for connec-
tion of a signal source which supplies an S-Video
signal
13 Video output S-VIDEO (mini DIN, 4-pole) to pass
on the fed-through signal of the input S-VIDEO (12)
to another unit
14 15-pole D-Sub connection VGA for connection to
the VGA output of a PC
15 3.5 mm stereo jack PC AUDIO for connection to the
audio output of a PC
16 Audio input AUDIO 2 (phono, stereo) for connec-
tion to the audio output of the signal source con-
nected to the input VIDEO 2 (18)
17 Audio output AUDIO 2 (phono, stereo) to pass on
the fed-through signal of the input AUDIO 2 (16) to
another unit
18 Video input VIDEO 2 (BNC) for connection of a sig-
nal source which supplies a composite video signal
and "Up" to navigate in the
19 Video output VIDEO 2 (BNC) to pass on the fed-
through signal of the input VIDEO 2 (18) to another
unit

2 Safety Notes

The units (monitor and power supply unit) correspond
to all required directives of the EU and are therefore
marked with .
WARNING The power supply unit is supplied with
hazardous mains voltage. Leave servic-
ing to skilled personnel only. Inexpert
handling or modification of the unit may
cause an electric shock hazard.
It is essential to observe the following items:
The units are suitable for indoor use only. Protect
them against dripping water and splash water, high
air humidity, and heat (admissible ambient tempera-
ture range 0 – 50 °C).
Do not place any vessels filled with liquid, e. g. drink-
ing glasses, on the units.
The heat being generated in the monitor must be
carried off by air circulation. Therefore, the air vents
at the housing must not be covered.
Do not set the monitor into operation, or immediate-
ly disconnect the mains plug of the power supply unit
from the mains socket if
1. there is visible damage to the monitor, the power
supply unit, or the mains cable,
2. a defect might have occurred after a drop or simi-
lar accident,
3. malfunctions occur.
The units must in any case be repaired by skilled
personnel.
Never pull the mains cable of the power supply unit
to disconnect the mains plug from the mains socket,
always seize the plug.
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
No guarantee claims for the units and no liability for
any resulting personal damage or material damage
will be accepted if the units are used for other pur-
poses than originally intended, if they are not cor-
rectly connected, operated, or not repaired in an
expert way.
Important for U.K. Customers!
The wires in the mains lead of the power supply unit
are coloured in accordance with the following code:
green/yellow = earth, blue = neutral, brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured green and yellow must
be connected to the terminal in the plug which is
marked with the letter E or by the earth symbol
or coloured green or green and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
GB
9