EdilKamin FANTASY Instrucciones De Uso página 39

Automatic mode from synoptic panel/remote control
Press the MENU button twice to switch from manual to
automatic mode and adjust the temperature desired for the
room (on the panel or the + and – keys on the remote control
to set the temperature between 10 and 29 ...., and the stove will
regulate the operating power required to reach it.
If the set temperature is lower than the room temperature,
the stove works at Power 1.
Shutdown
For greater comfort, the stove and the air vents go off
at the same power at which it was operating.
With the stove in operation mode press the 0/1 key for 2
seconds (on the synoptic panel or remote control). The
shutdown procedure will begin and the countdown is
displayed. This varies according to the power at which it
is running when the shutdown phase begins.
The shutdown phase (which will extinguish the ame
without leaving any unburnt material in the combustion
chamber and cool the stove), consists of:
• Pellet loading ceases.
• Ventilation is activated at the level at which the stove
was operating.
• Smoke expulsion motor enabled.
Never unplug the stove during the shutdown process.
Setting the clock
Press the MENU button for 2 seconds and use the + and –
keys to follow the instructions given on the display to
access the 'Clock' menu. This allows you to set the time on the
electronic control board.
Then press MENU and the following data appears in
sequence – this can be adjusted:
day, month, year, hour, minutes, day of the week.
When 'Save?' appears on the display you can check that
the settings have been entered correctly before con rming.
Press MENU to save the information ('Save OK' then
appears on the display).
Weekly timer
Press the MENU button on the remote control for 2
seconds to access the time setting function and press the
+ key to access the weekly timer function – 'Program ON/
OFF' will appear on the display.
A maximum of three timer programs can be set for each
day of the week.
As you con rm via the MENU button, one of the following
options will appear:
- 'No Prog.' (no program is set).
- 'Daily program' (a single program is set for every day)
- 'Weekly program' (a program is set for each day of the
week).
Move from one to the other using the + and – keys.
Use the MENU button to con rm the 'Daily program'
option and access the selection of the number of programs
(ignition/shutdown) to be set per day. Use the 'Daily program'
option to set the identical program/s for every day
of the week.
INSTRUCTIONS FOR USE
- 39
The following will be displayed if the + key is pressed:
- No Programs.
- 1st daily program (one ignition and one shutdown per
day), 2nd daily program (same as before), 3rd daily program
(same as before).
Use the MENU button to show them in reverse order.
If the 1st program is selected, the ignition time is shown.
The display shows: 1 Ignition Hour 10.30; use the +/–
keys to change the hour and press MENU to con rm.
The display shows: 1 Ignition Minutes 10.30; use the +/–
keys to change the minutes and press MENU to con rm.
In the same way, adjust the shutdown times. The program is
con rmed by pressing the MENU button when 'Save OK' ap-
pears on the display. When con rming the 'Weekly program'
the day to which the program is to apply must be selected:
1 Mon; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sat; 7 Sun
Once you have chosen the day by scrolling through them
with the + and – keys, con rm by pressing MENU and
proceed with the settings of the programs in the same way
as for the 'Daily program', selecting whether or not to
enable a program for each day of the week and choosing
the number and times of interventions.
Should you make a mistake whilst setting the programs
you can exit without saving by pressing the 0/1 key.
Note on ame variability
The ame may vary depending on the type of pellets
used, in addition to normal variability of the solid fuel
ame and regular cleaning of the combustion chamber
carried out automatically by the stove.
N.B. The automatic cleaning process performed by the
stove does not replace the need for the user to vacuum the
stove when cold, prior to ignition).
Pellet reserve warning
Stoves are equipped with an electronic pellet detection
system. The detection system is integrated into the electronic
control board, allowing the stove to monitor how many kilos
of pellets are left. This veri cation is implemented at any point
whilst the stove is in operation mode. For correct system ope-
ration, it is important that the following procedure is adhered
with during the rst ignition (that must be implemented by the
DEALER). Before starting to use the pellet detection system,
you must load and consume a full sack of pellets. This allows
for a brief running-in of the loading system. Hence, load 15 kg
of pellets. Then press the 'reserve' button once, thereby storing
the data into the memory that 15 kg have been loaded.
From now on the display will show the remaining pellets
as they decrease in kg (15...14...13).
Each time pellets are reloaded you must enter the quantity.
E.g. when loading 15 kg, simply press the 'pellet load' button
to enter this into the memory. For other quantities, or in the
event of an error, you can specify the quantity using the pellet
reserve menu as follows:
Press the MENU button for 2 seconds to view the SETTINGS.
Press + or – consecutively to view RESERVE.
Pressing the + key increases the Kg to be loaded, pressing the -
key reduces the Kg, pressing the - key repeatedly sets the load
to 00Kg (R on the display), which makes it possible to cancel
the residual load.
-