Programmable Functions - PIAGGIO 1D001230 Instrucciones De Uso

DESCRIPTION:
To adapt the system to different needs of the local markets and boost the functional flexibility, avoiding
however to compromise its user-friendly character, it is possible to program additional functions. The system
is generally supplied with most of these functions disabled; the installer or final client will personalize the
functions deemed appropriate to use the vehicle as required. The functions are listed below:
FUNCTION
Air bag reminder
PIN 8 input configuration of the main
connector
ON/OFF alarm sound signals
Passive
Accidental anti-disabling
Pre-alarm
Anti-theft
Modules output programming
Exclusion of TILTING sensor
ENABLING/DISABLING MODE OF THE PROGRAMMABLE FUNCTIONS:
In order to program one of the functions previously described, follow the indications below:
1. Enable and disable the activation panel three times, at the third activation, leave it on.
2. Wait approx. 0.5 sec. between one activation and the other of the panel.
3. Upon the third activation (leaving the panel on), the led will emit a series of flashing to notify the input in
programming mode.
4. Press key C of the remote control within 5 sec., the alarm will emit three sound signals combined to
three flashing of the led.
5. Afterwards, the system will prompt the turn signals to flash quickly, it will emit a sound signal in grave
tone and turn off the led, thus indicating that it is on the first function (one flashing of the turn signals
combined to a sound signal) and that this is deactivated. From this moment, it is possible to set the first
function (air bag reminder signals). The led off will notify that the function is not active. If you wish to
activate the function in object, simply press key "B" of the remote control; the led will turn on and a sound
signal in acute tone will be emitted to confirm activation. To switch to the programming of function 2
(Configuration of perimetric input), press key "C" of the remote control; the alarm will emit two sound
signals and two flashing of the turn signals, confirming the possibility to set function 2 (Switch of pin 8
between operation as perimetric input or air bag reminder management). The led on will notify that the
function is active. If you wish to deactivate the function in object, simply press key "B" of the remote
control; the led off and the emission of a sound signal in grave tone will confirm deactivation.
6. This procedure is identical for all functions. The number of flashing of the turn signals and emission of
sound signals will indicate which is the function being programmed.

PROGRAMMABLE FUNCTIONS

DESCRIPTION
It enables the optical/ sound signals to assist the vehicle's user in the
proper use of the safety equipment implemented in the technical
It selects the operation mode of the perimetric input (PIN 8 of the
main connector).
Function OFF: PIN 8 will work as perimetric input.
Function ON: PIN 8 will work as AIR BAG reminder signalling block.
It enables the sound signals upon alarm enabling, disabling and in
alarm memory status.
After 30 sec. from turning the panel off, if the alarm is not engaged,
the vehicle's engine will be automatically blocked. The function's
activation will be signalled with the emission of a sound signal. The
engine start-up attempt with the passive function engaged, will be
notified with the emission of a serious of sound signals. To deactivate
this function, simply engage and disengage the alarm using key A of
the remote control or carry out this operation using the electronic key.
After 30 sec. from disengaging the alarm, if the vehicle is not moved
or used, this will be reset automatically.
If an alarm condition is triggered, the siren will be activated for 5 sec.
If a new alarm cause is triggered in the next 30 sec., the siren will be
activated for 30 sec.
By pressing key A of the remote control with the panel on, the system
will emit a quick flashing of the turn signals, after 30 sec. the siren will
be activated, and after an additional 3o sec., the engine block will be
activated. It is possible to disengage the anti-theft function only with
the electronic key or PIN CODE. The engine cannot be started up for
the entire duration of the anti-theft function, and the siren will be
activated in continuous mode for 30 sec. with a pause of 10 sec.
between a buzz and the other.
NOTE: In order to activate the anti-theft function from the remote
control, the activation panel must be enabled for at least 5 sec.
It allows selecting the management mode of the output on pin 12:
ON: Positive output of auxiliary modules.
•
OFF: (positive) control of the seat actuator
•
It allows to completely exclude the tilting sensor.
supply.
SETTING (FACTORY)
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
(Control of
seat
actuator)
Sensor ON