Electrical Safety; Replacing The Power Cable; Safety Information; Motor Safety Switch - IKRA IEVL 1400 Instrucciones De Manejo

• Replace worn or damaged parts for reasons of safety.
Use only original spare parts. Parts not produced by
possibly cause injury.
•
the tool with only one hand.
• Hold the guide bar and lift the tool to move it from
one place to another. Always switch off the tool, dis-
connect the plug and wait until the application stops
before carrying out maintenance.

Electrical safety

• The electric motor has been designed to use single
phase voltage only.
• Make sure your voltage corresponds to the one writ-
ten on the rating label.
Your machine has double insulation in
conformity to Directive EN 60335, you do
not therefore need to earth.
• Always use a plug compulsory for double insulation
electric tooling when replacing the cable.
• Always switch your machine off before disconnecting
any plug, socket or extension.
• Increased safety can be obtained by having a quali-
breaker in the house wiring. If you do not have such
a circuit breaker installed, or you do not wish to have
one installed, then we strongly recommend that the
electrical power to your Machine be supplied through
a high sensitivity (30mA) residual current device
(RCD). The RCD is designed to provide a high degree
of personal protection against harmful electric current
should fault conditions occur.

Replacing the power cable

If the power cable of the device should be damaged it
must be replaced by the manufacturer or their after-sales

6. SAFETY INFORMATION

Motor safety switch

The motor safety swich turns off the motor in the event of
a capacity overloaded. The function of the motor safety
switch may not be taken out of operation.
If the motor safety switch has turned off the appliance,
proceed as follows:
1. Disconnect the appliance from the power supply
2. Correct the caue for the capacity overload.
3. After a cooling time of 2 to 3 minutes, connect it again
to the power supply and start the appliance up again

Safety switch bar

The appliance is equippied with a safety switch bar that
turns off the appliance as soon as it is let go.
Danger!
The function of the safety switch bar may not be
taken out o operation.
GB | Operating Instructions

Back Cover

The equipment is equipped with a back cover.

7. UNPACKING/MOUNTING

1. Remove the appliance from the packaging.
2. Check the content for completeness. In the event of
3. Execute the assembly of the components according

8. OPERATION

Commissioning
Adjusting the working depth (picture B)
a) Press the handle to lift the front axle and to discharge
b) Push the depth adjustment lever towards the wheel,
Connection to power supply (picture C)
1. Insert the coupling member of the power cable to the
2. Form a loop from the power cable and slide it into the
3. Always route the electric main cable away from the
Switching the motor on (picture D and E)
1.
2.
3.

Switching the motor off

1. Let go of the safety handle. The safety handle auto-
GB-7
Danger!
Only put the appliance into operation after assem-
bly of all parts has been completed.
to the assembly plan A.
Danger!
Only with the motor switched off and the roller at
a standstill.
the front wheels.
then move it forward or backward to adjust the cutting
depth. (See Fig. B). Adjust the lever to one out of the
four stages.
Danger!
Operate the appliance only, when no parts (e.g.
connection line is free of damages.
plug of the spring-loaded safety push button.
cable relief. The loop of the power cable must be long
enough to be able to slide from one side to the other.
work area to prevent it from coming into contact with
the cutting device. Plan your route before starting
work. Start your work at the nearest point to the elec-
trical outlet, and work away from it. This will keep the
cable away from the cutting device and avoid it being
accidentally cut. Keep the cable over your shoulder
for added safety.
Press the safety push button and keep pressed.
Pull the safety handle against the bar. The motor
starts.
Note:
The safety handle does not engage. It must be
hold all the time.
Let go the safety push button.
(picture A)