General Operation; Maintenance - IKRA IEVL 1400 Instrucciones De Manejo

matically returns to the zero position. The motor is now
turned off.
Danger!
After the motor has been switched off, the roller
continues to rotate for a few seconds – therefore,
do not put your hands under the appliance straight
away.

9. GENERAL OPERATION

WARNING!
time of the day and on what special days products are
allowed to be used and what restrictions apply!
Ask your community for detailed information and observe
the regulations in order to preserve a peaceful neighbor
hood and avoid committing administrative offences!
WARNING! If the product strikes a foreign object stop
the motor! Switch the product off, disconnect it from the
power supply and let it cool down. Inspect the product
thoroughly for damage! Have any damage repaired be-
fore restarting!
WARNING! Extensive vibration of the product during op-
eration is an indication of damage! The product should be
promptly inspected and repaired!
1. Check the product, its power cord and plug as well as
accessories for damage before each use. Do not use
the product if it is damaged or shows wear.
2.
3. Push the product forward by its handle. Keep the han-
dle dry to ensure safe support.
4. Ensure that the air vents are always unobstructed
and clear. Clean them if necessary with a soft brush.
Blocked air vents may lead to overheating and dam-
age the product.
5. Switch the product off immediately if you are disturbed
while working by other people entering the working
area. Always let the product come to complete stop
before putting it down.
6. Do not overwork yourself. Take regular breaks to en-
sure you can concentrate on the work and have full
control over the product.
7. Mow the lawn before working and fertilise afterwards.
8. Make sure that the lawn is clear of stones, sticks, wire
or other objects that could damage the product or its
motor.
9. Select the suitable cutting depth for the actual grass
height.
10. Do not work with this product on a wet lawn because
it tends to stick to the underbody of the product, pre-
venting the proper discharge of collected material,
and it could also cause you to slip and fall.
11. Slowly push the product forward. Move the product at
appropriate speed. Do not move it too fast to prevent
the discharge opening from getting blocked and en-
gine from useless overloading.
12. Work in slight overlapping rows. The most effective
pattern for scarifying/raking lawns is straight lines
along one of the sides. This will keep the rows even
out missing any spots. (See Fig. 10).
GB | Operating Instructions
13.
14. Pay special attention when changing direction.
15. Never tilt or transport appliance with running motor
16. Never leave the appliance unattended.
17. When leaving, disconnect the appliance from the
Checking by an expert is necessary
-after hitting an obstacle
-if the motor comes to an immediate standstill
-if the toothed belt is defective
-if the wire leading to the motor is damaged
-if there are other damages.

10. MAINTENANCE

SERVICE AND STORAGE
To ensure long and reliable service, carry out the follow-
ing maintenance regularly. Servicing and cleaning work
on the product and the removal of the guards may only
be carried out after the motor has been switched off and
the plug disconnected from the power supply.
1. Regularly check for obvious defects such as loose,
2. Check that covers and guards are undamaged and
3. If the cutting device should happen to fail despite the
4. Do not clean the product while it is running.
5. Ensure that all the fastening elements (screws, nuts,
6. Check the product frequently for signs of wear. Re-
7. Store your product in a dry place. To ensure a long
8. Clean the product with a brush or cloth. Do not use
9. The component that is subject to most wear is the
-
GB-8
bed in the middle of the lawn, make a row or two
around the circumference of the bed.
power supply.
WARNING! Before carrying out any repairs or
servicing work, you must ensure that the prod-
uct has been disconnected from the power sup-
ply. Repairs and maintenance work other than
described within this instruction manual may be
ings and worn or damaged components.
repairs before using the product.
care taken in manufacturing and testing, repair should
be carried out by an authorized specialist.
etc.) are tight at all times so that you can safely work
with the product.
place worn or damaged parts.
service life all screw parts should be cleaned and then
oiled.
any solvents or water to remove dirt.
cutting device. You should therefore check the condi-
tion of the cutting device and its mounting at regular
intervals.
- If the cutting device is worn or blunt it must be re-
placed immediately;
- If the product starts to suffer from excessive vibra-
tions, this means that the cutting device has not
-