Operation And Use - Topcom BABYVIEWER KS-4248 Manual De Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 25
Babyviewer - KS-4248 KS-4249
CAUTION
Do not place the camera and wires within the baby's reach!
Fix the camera at least 1 meter away from the baby.

10 Operation and use

10.1
Switching the baby unit and parent unit on
and off
– Press and hold the on/off button
parent unit. The display
– Slide the on/off switch
unit. The on/off LED
The parent unit will try to establish a connection
with the baby unit. If captured image from the
camera is displayed, a connection has been
established.
– Press the on/off button
unit (press and hold until the display goes blank).
– Slide the on/off switch
baby unit.
10.2
Checking the connection between the parent
unit and the baby unit
You should always check the wireless connection when you use
the babyphone for the first time.
– Put the parent unit in the same room as the baby unit,
separated by at least two meters.
– Switch on both devices. The parent unit will try to
establish a connection with the baby unit.
– The display of the parent unit will show the captured
image from the baby unit after the connection has been
established (monitor mode).
– The sounds picked up by the microphone
reproduced by the parent unit.
– The volume of the reproduced sound is indicated by the
volume LED's
at the top of the parent unit.
14
The higher the volume, the more LED's are on.
– If no connection is established, "OUT OF RANGE" is
displayed.
10.3
Out of range indication
The maximum range between the parent- and baby unit is 300
meter in open area. Different factors, such as bricks and plaster
walls, will reduce the range. Moreover, reinforced concrete floors
will influence the range tremendously.
In a residence, normal operating range is up to 50 meters and 2
floors.
– If the connection is interrupted, "OUT OF RANGE" is
displayed.
– Reduce the distance between the parent and baby units
until a new connection is established.
to switch on the
224
19
is activated.
up to switch on the baby
4
is activated.
24
to switch off the parent
down to switch off the
4
are
6
10.4
Setting the reproduction volume of the
parent unit
There are 5 volume levels.
15
– Press button
to increase the volume.
16
to decrease the volume.
– Press button
10.5
Setting the parent unit display brightness
There are 5 brightness levels. When the display is on:
16 18
– Press button
to increase the brightness.
– Press button
to decrease the brightness.
17 17
10.6
Temperature indication
When the display is on, the baby's room temperature is displayed
in the top right corner.
10.7
Temperature alert
You can set a high/low temperature alert, the unit will give beep
when the temperate will go beyond the preset range.
– Press the menu button
Use the arrow keys to highlight items, and use the menu
button
to confirm your selection. Use the On/Off
23
button to go back one step.
– Enter the temperature menu to turn the temperature
alert function on or off.
– Use the arrow keys to set the lowest temperature
between 5°C and 24°C
– Next, use the arrow keys to set the highest temperature
between 25°C and 40°C
10.8
Zoom function
The parent unit has X2 zoom digital view function.
– When parent unit in X1 viewing mode, press and hold
the up button
23 16
– The live viewing area will change to X2 zoom mode
immediately.
– Press and hold the down button
zoom.
10.9
Talking with your baby
You can use the parent unit to talk with your baby.
Allow your baby to get used to the talk function
before you use it in practice.
– Press the Talk button
it pressed.
– Hold the parent unit vertical with the microphone
approximately 10 cm from your mouth, and speak into
the microphone.
– Release button
24
10.10 Playing a lullaby
There are 5 pre-programmed lullabies that you can play on the
baby unit.
– Go to the main menu with the menu button
enter the lullaby menu. You can turn the lullaby on or off
in this menu.
– To select a different lullaby, enter the songs menu and
select on of the 5 lullabies.with the menu button
10.11 Switching the night light on and off
– Go to the main menu with the menu button
enter the night light menu. You can turn the night light on
or off in this menu.
10.12 Voice activated transmission (VOX)
During night and to save energy, the babyviewer can be set in
VOX mode.
In VOX mode, the display will be activated as soon as the
microphone of the baby unit will capture sound.
You can set the sound detection sensitivity (VOX) of the
babyphone. If the sensitivity is set to high, the baby unit will pick
up weaker sounds.
Press the menu button
Use the arrow keys to highlight items, and use the menu
to enter the main menu.
22
for 2 seconds,
to go back to X1
23 17
on the parent unit and hold
24
when you have finished talking.
and
23
and
23
to enter the main menu.
23
®
.
23
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Babyviewer ks-4249

Tabla de contenido