Operation And Use - Topcom BABYVIEWER KS-4240 Manual De Usuario

Babyviewer - KS-4240
9 Installing the Babyviewer KS-4240
9.1 Fine tuning
• Place the camera in a convenient location, point the lens of
the camera to the observation area.
• Adjust the angle by rotation the camera.
CAUTION
Do not place the camera and wires within the baby's reach!
Fix the camera at least 1 meter away from the baby.

10 Operation and use

10.1 Switching the baby unit and parent unit on
and off
– Press the on/off button
unit. The display is activated.
20
– Slide the on/off switch
unit. The on/off LED
The parent unit will try to establish a connection
with the baby unit. If captured image from the
camera is displayed, a connection has been
established.
– Press the on/off button
unit (press and hold until the display goes blank).
– Slide the on/off switch
baby unit.
10.2 Baby phone mode.
The Babyviewer can also be used as a audio babyphone, this is
an option to save energy. Follow the procedure below.
– Make sure the VOX mode is off, see the VOX paragraph
for instructions (See "10.13 Voice activated transmission
(VOX)").
– Press the on/off button
babyphone modus.
– Press the on/off button
display again.
10.3 Checking the connection between the parent
unit and the baby unit
You should always check the wireless connection when you use
the babyphone for the first time.
– Put the parent unit in the same room as the baby unit,
separated by at least two meters.
– Switch on both devices. The parent unit will try to
establish a connection with the baby unit.
– The display of the parent unit will show the captured
image from the baby unit after the connection has been
established (monitor mode).
– The sounds picked up by the microphone
reproduced by the parent unit.
– The volume of the reproduced sound is indicated by the
volume LED's at the top of the parent unit.
14
The higher the volume, the more LED's are on.
– If no connection is established, "OUT OF RANGE" is
displayed.
10.4 Out of range indication
The maximum range between the parent- and baby unit is 300
meter in open area. Different factors, such as bricks and plaster
walls, will reduce the range. Moreover, reinforced concrete floors
will influence the range tremendously.
In a residence, normal operating range is up to 50 meters and 2
floors.
– If the connection is interrupted, "OUT OF RANGE" is
displayed.
– Reduce the distance between the parent and baby units
until a new connection is established.
to switch on the parent
25
up to switch on the baby
4
is activated.
to switch off the parent
25
down to switch off the
4
to go to audio
25
again to turn on the
25
are
6
10.5 Setting the reproduction volume of the
parent unit
There are 5 volume levels.
– Press button to increase the volume.
16
– Press button to decrease the volume.
17
10.6 Setting the parent unit display brightness
When the display in on.
– Press the menu button
icon is displayed.
– Press the up or down button
16
desired brightness (5 steps).
– Press the menu button
– After 10 seconds the parent unit will switch back to
monitor mode.
10.7 Temperature indication
When the display is on, the baby's room temperature is displayed
in the right lower corner.
To set the temperature unit:
– Press the menu button
icon is displayed.
– Press the up or down button
16
(Celsius), °F (Fahrenheit).
– Press the menu button
– After 10 seconds the parent unit will switch back to
monitor mode.
10.8 Temperature alert
You can set a high/low temperature alert, the unit will give beep
when the temperate will go beyond the preset range.
– Press the menu button
temperature between 25°C and 39°C.
– Press the menu button
temperature between 10°C and 24°C
– You can change the temperature by pressing the up
or down button
16
– To turn off the temperature alert, select OFF in both
modes.
10.9 Zoom function
The parent unit has X2 zoom digital view function.
– When parent unit in X1 viewing mode, press and hold
the the menu button
– The live viewing area will change to X2 zoom mode
immediately. At the same time, four direction arrows are
displayed at the middle of the screen.
– Press the up button
move the screen up and down.
– Press the camera button
left
– Press the music button
right
– Press the menu button
monitor mode.
Switch back to X1 viewing mode
– When parent unit is in X2 zoom mode, press and hold
the menu button
23
– X1 magnification icon appears and the screen becomes
X1 viewing mode.
– Press the menu button
mode
10.10 Talking with your baby
You can use the parent unit to talk with your baby.
Allow your baby to get used to the talk function
before you use it in practice.
– Press the Talk button
it pressed.
– Hold the parent unit vertical with the microphone
approximately 10 cm from your mouth, and speak into
the microphone.
– Release button
24
once. The Brightness
23
to select the
17
to confirm.
23
twice. The temperature
23
to °C
17
to confirm.
23
3 times to set the highest
23
4 times to set the lowest
23
.
17
for 2 seconds,
23
or down button to
16 17
to move the screen to
19
to move the screen to
18
key to go back to the
23
for 2 seconds.
to go back to monitor
23
on the parent unit and hold
24
when you have finished talking.
5
®