Operation And Use - Topcom BABYVIEWER 4400 Manual De Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 25
Babyviewer 4400

10 Operation and use

10.1
Switching the baby unit and parent unit on
and off
– Press the on/off switch
15
The display
is activated.
16
– Press the on/off switch
on/off LED
is activated.
4
The parent unit will try to establish a
connection with the baby unit. If captured image
from the camera is displayed, a connection has
been established.
– Press and hold the on/off switch
unit until the display goes blank.
– Press the on/off switch
10.2
Checking the connection between the parent
unit and the baby unit
You should always check the wireless connection when you use
the babyphone for the first time.
– Put the parent unit in the same room as the baby unit,
separated by at least two metres.
– Switch on both devices. The parent unit will try to establish
a connection with the baby unit.
– The display of the parent unit will show the captured image
from the baby unit after the connection has been
established (monitor mode).
– The sounds picked up by the microphone
reproduced by the parent unit. The sound level is indicated
in the bottom of the display.
– If no connection is established, a repeating beep is audible.
10.3
Out of range indication
The maximum range between the parent- and baby unit is 200
meter in open area. Different factors, such as bricks and plaster
walls, will reduce the range. Moreover, reinforced concrete floors
will influence the range tremendously.
In a residence, normal operating range is up to 50 meters and 2
floors.
– If the connection is interrupted, a repeating beep is audible.
– Reduce the distance between the parent and baby units
until a new connection is established.
11 Settings
11.1
Setting the volume of the parent unit
There are 7 volume levels.
– Press button
to increase the volume.
19
– Press button
to decrease the volume.
21
11.2
Setting the display brightness
When the display in on.
– Press the menu
button. The
22
setting menu is displayed.
– Press the +
button until the
19
wrench symbol is highlighted.
– Press the OK button
.
17
– Press the +
or - button
19
select the desired brightness icon
– Press the +
or - button
19
select the desired brightness (7
steps).
– Press the OK button
17
– Press the menu button
22
11.3
Mirror the image
Depending the position of the camera, it can be necessary to
mirror or rotate the image.
to switch on the parent unit.
to switch on the baby unit. The
9
to switch off the parent
15
to switch off the baby unit.
9
are
7
to
21
to
21
to confirm.
2 times to leave the menu.
.
– Press repeatedly on the menu
button until the wrench symbol is
highlighted.
– Press the OK button
17
– Press the +
or - button
19
select the
to mirror the image of
to rotate the image 180°.
– Press the +
or - button
19
select the desired image.
– Press the OK button
17
– Press the menu button
22
11.4
Temperature indication
When the display is on, the baby's room
temperature is displayed in the middle of
the display.
An alarm can be set when the temperature
reaches the upper or lower limit.
– Press the menu
button. The
22
setting menu is displayed.
– Press the +
button until the
19
temperature symbol is highlighted.
– Press the OK button
17
– Press the +
or - button
19
select the change the upper limit.
– Press the OK button
17
– Press the +
or - button
19
lower limit.
– Press the OK button
17
– Press the menu button
22
When the room temperature is exceeding the limits, a audio signal
is audible and the temperature flashes on the display.
11.5
Setting the clock
When the display is on, the clock is
displayed on top of the display.
To set the clock
– Press the menu
button. The
22
setting menu is displayed.
– Press the +
button until the clock
19
symbol is highlighted.
– Press the OK button
17
clock setting icon.
– Press the OK button
17
The hour indication is red.
– Press the +
or - button
19
– Press the OK button
17
is red.
– Press the +
or - button
19
– Press the OK button
17
To select the time format after setting the time.
– Press the +
or - button
19
hours.
– Press the OK button
17
– Press the +
or - button
19
24 hours.
– Press the OK button
17
– Press the menu button
22
11.6
Night light
The Babyviewer 4400 has a night light from
which the intensity changes depending on
the environment.
The night light can be remotely activated.
Make sure that the night light switch
the baby unit is set to 'On'
– Press the menu
button. The
22
setting menu is displayed.
– Press the +
button until the
19
night light symbol is highlighted.
– Press the OK button
17
– Press the +
or - button
19
light setup.
22
.
to
21
to
21
to confirm.
2 times to leave the menu.
.
to
21
.
to select the change the
21
to confirm.
2 times to leave the menu.
to select the
to confirm.
to change the hour.
21
to confirm. The minutes indication
to change the minutes.
21
.
to select AM/PM or 24
21
to confirm.
to switch between AM/PM or
21
to confirm.
2 times to leave the menu.
on
11
.
to select the desired night
21
®
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ks-4244

Tabla de contenido