Dust Extraction; Working With The Electric Power Tool; Sawing Cut-Outs (Plunge Cuts) - Festool HK 55 EBQ Manual De Instrucciones

Ocultar thumbs Ver también para HK 55 EBQ:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 32
HK 55
GB
Remove saw blade[5-9].
Insert new saw blade.
The direction of rotation of the saw blade
[5-7] and saw [5-6] must match.
Insert the outer flange [5-8]so that the pin en-
gages in the recess on the inner flange.
Release retractor lever [5-5] and allow the pen-
dulum guard to swivel back [5-11] to its final
position.
Tighten screw [5-10].
Reposition lever [5-4] .
Risk of injury! Whenever you replace a saw
blade, always check that it is securely in
place. If a clamping flange is loose, the cut-
ting edges of the saw blade may break off, and if a
screw is loose, the saw blade may become de-
tached.
7.6

Dust extraction

WARNING
Dust hazard
Dust can be hazardous to health. Always work
with a dust extractor.
Always read applicable national regulations be-
fore extracting hazardous dust.
Festool mobile dust extractor
A Festool mobile dust extractor with an extractor
hose diameter of 27 mm or 36 mm (36 mm is rec-
ommended due to the reduced risk of clogging) can
be connected to the extractor connector [1-10] at
the elbow.
– Static charge may occur if an anti-static suction
hose is not used. The user may suffer an electric
shock.
Independent extraction
Secure the connection piece [6-2] of the dust
collection bag [6-3] at the extractor connector
with a clockwise rotation [6-1].
To empty remove the connection piece [6-2]of
the dust collection bag [6-3]from the extractor
connector with an anti-clockwise rotation [6-1].
8

Working with the electric power tool

Please observe all mentioned safety infor-
mations and the following rules when work-
ing:
– Only guide the machine against the workpiece
when it is switched on.
20
– Check the function of the pendulum guard prior
to use and do not use the electric power tool if it
does not slide in and out easily.
– Always secure the workpiece in such a manner
that it cannot move while being processed.
– Always hold the machine with two hands at the
handles [1-1] when performing work. This re-
duces the risk of injury and is a prerequisite for
precise work.
– Always push the saw forwards [8-9], and never
towards yourself.
– Adapt the infeed speed to prevent the cutters on
the saw blade from overheating and prevent
plastic materials from melting during cutting.
– Make sure that the knob [1-12] is tightened be-
fore starting work.
– Do not use the machine when the electronics are
faulty because the machine may operate at ex-
cessive speeds. An absence of the smooth start-
up function or speed control indicates that the
electronics are faulty.
8.1
Sawing along the scribe mark
The cut indicators display the cutting sequence
without a guide rail:
0° cuts: [7-1]
45° cuts: [7-2]
8.2
Cutting sections
Position the saw with the front part of the saw table
on the workpiece, switch on saw and push forward
in cutting direction.
8.3

Sawing cut-outs (plunge cuts)

In order to avoid kickbacks, the following in-
structions must be observed without fail
when plunge cutting:
– Always position saw with the rear edge of the saw
table against a fixed stop.
– When working with the guide rail, place the saw
against the kickback stop FS-RSP (accessories)
[8-6] clamped to the guide rail.
Caution! Danger of crushing!
Always keep a firm grip on the machine with
your free hand when adjusting plunge cuts. Never
position your fingers behind or below the saw
blade.
Procedure
Adjusting cutting depth, see section 7.2.
Press lever [8-1] down.
Sawing unit swivels upwards to plunge-cut po-
sition.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hk 55 eq10008474200162

Tabla de contenido