Recording The Performance (Usb Recording Section); About The Auto Standby Function - Pioneer DJM-350 Manual De Instrucciones

3 Turn [LEVEL] 4 in the MIC/ AUX section clockwise.
The sound of the microphone or external device is output from the
speakers.
Adjusting the sound quality
Turn [HI] or [LOW] 5 in the MIC/ AUX section.
Refer to Specifications on page 16 for the range of sound that can be
adjusted by each control.
Recording the performance (USB
recording section)
The same sound as the sound being output from the [MASTER OUT 1,
2] terminals can be recorded as a WAV file on a USB device.
! The name of the files created when the sound is recorded is in the
format [REC***.WAV] (*** is a 3-digit number).
1 Insert the USB device into the USB device insertion
slot k.
The [USB STOP] indicator l flashes.
After a while, the [USB STOP] indicator stops flashing, remaining lit,
and the recording standby mode is set.
2 Press [REC k/ g] m.
Recording starts.
The [REC k/ g] indicator m flashes.
! When [REC k/ g] is pressed again, the [REC k/ g] indicator turns
off and recording stops.
! Continuous recording is possible for 180 minutes. If recording con-
tinues for over 180 minutes, the recording data on the USB device
is automatically split.
! Recording is possible for about 90 minutes on a 1 GB USB device.
Playing recorded tracks
Press [PLAY f] n.
Playback starts.
The [PLAY f] indicator n lights.
! When [PLAY f] is pressed again, playback is paused.
! Only WAV files stored in the [PIONEER DJM / DJM350 REC] folder
on the USB device can be played.
Previewing recorded tracks
1 Turn [MIXING] 8 counterclockwise from the center
position.
2 Press and hold in [TRACK MARK (PREVIEW)] o.
The sound of the recorded track can be heard over the headphones
while the button is pressed.
! The sound being previewed is added to the sound of [CH-1] and
[CH-2] and output from the headphones.
! The sound being previewed is not output from the speakers.
12
En
k
l
USB
STOP
m n
REC PLAY


TRACK MARK SEARCH
 
o
p
PREVIEW
! Previewing is not possible while the track is being recorded or
played.
Fast-forwarding/ reversing recorded
tracks
During playback, press and hold in [SEARCH o, p] p.
The track is fast-forwarded when [p] is pressed and held in.
The track is fast reversed when [o] is pressed and held in.
The [PLAY f] indicator flashes during fast-forwarding/ reversing.
! Fast-forwarding/ reversing is not possible when in the pause mode.
 Cuing to the beginning of recorded tracks
Press [SEARCH o, p] p.
Press the [p] to move to the beginning of the next track.
Press [o] once to move to the beginning of the currently playing
track, twice to move to the beginning of the previous track.
Splitting tracks while recording
During recording, press [TRACK MARK (PREVIEW)] o.
The currently recording track is split and stored on the USB device.
! When split tracks are played on this unit, the sound may be inter-
rupted at the boundary between the two tracks.
Deleting recorded tracks
1 While playing the track, press [PLAY f] n.
The track you want to delete is paused.
2 Press [PLAY f] n for at least 2 seconds.
The [REC k/ g] indicator flashes.
3 While pressing [PLAY f] n, press [REC k/ g] m.
The [REC k/ g] indicator lights and the track is deleted.
! Track deleting is canceled if [PLAY f] is released while the [REC
k/ g] indicator is flashing.
Disconnecting USB devices
Always perform the following procedure to disconnect USB devices.
Pulling the USB device out without performing this procedure could
make the USB device unreadable.
When turning the set's power off, be sure to remove the USB device
first.
1 Press [USB STOP] l for at least 1 second.
The [USB STOP] indicator flashes, then turns off.
2 Disconnect the USB device.

About the auto standby function

When the auto standby function is turned on, the power is automati-
cally set to the standby mode after the set time has passed with all of
the conditions below met.
— That none of this unit's buttons or controls are operated.
— That this unit's channel level indicator is not lit.
— That the USB device's recording and playback functions are not in
use.
Setting the auto standby function
First set this unit to the standby mode.