About Errors; About Usb Devices/ Files Usable On This Unit - Pioneer DJM-350 Manual De Instrucciones

About errors

If this unit cannot operate normally, the [u] (the power switch), [USB STOP] and [PLAY f] indicators flash to indicate an error.
Check the table below and take the measures indicated.
If the same error is indicated after the measures have been taken, contact your store of purchase or nearby Pioneer service station.
About the [USB STOP] indicator's error indication
 If the [USB STOP] indicator flashes repeatedly 2 to 5 times
1 Disconnect the USB device.
2 Press [USB STOP].
Check the table below and take the measures indicated.
Number
Indicator of times Description of
name indicator error
flashes
2 times
File format problem
repeatedly
3 times
USB class problem
repeatedly
USB STOP
4 times Problem writing
repeatedly on the USB device
5 times USB device over-
repeatedly current detected
3 times Playback error
PLAY f
u (power
Continuous Circuit problem
switch)
About USB devices/ files usable on
this unit
This unit supports external hard disks, portable flash memory devices
and other USB mass storage class devices.
Folder layers Max. 2 layers (PIONEER DJM / DJM350 REC)
Max. number of
Maximum 999 tracks
files
Supported file
FAT, FAT32 and HFS+
systems
! Optical disk type devices such as external DVD/ CD drives, etc., are not sup-
ported.
! When there are many folders or files, some time may be required for load-
ing.
! If multiple partitions are set for the USB device, the device may not be
recognized.
Cautions on using USB devices
! Some USB devices may not operate properly. Please note that
Pioneer will accept no responsibility whatsoever for loss of data
recorded on USB devices.
Cause
USB device is not formatted.
You are using a USB device with a file system that is not
supported by this unit.
A device other than a USB mass storage class device is
connected.
A USB hub is connected.
Not enough free space on the USB device.
There is a file name "REC999.WAV" in the recorded data
storage folder (PIONEER DJM / DJM350 REC).
USB device's write protect switch is set to the on posi-
tion.
You are using a USB device with a security function.
The recorded data storage folder (PIONEER DJM /
DJM350 REC) is set to "Read Only".
You are using a USB device (such as a bus power-driven
hard disk) whose current is higher than this unit's rated
current (500 mA).
There are no playable files in the recorded data storage
folder (PIONEER DJM / DJM350 REC).
There is a problem in the internal circuitry.
! USB hubs cannot be used.
! USB devices equipped with flash card readers may not operate.
! It may happen that, when a current stronger than the maxi-
! Depending on the USB device you are using, the desired perfor-
About WAV files
The DJM-350 supports WAV files in the formats shown below.
Compatible
formats
File extension
Measure
Use a USB device formatted with a file system sup-
ported by this unit (FAT or HFS+).
Connect a USB mass storage class USB device.
Do not connect USB hubs.
Use a USB device with sufficient free space.
Files created through recording are given a 3-digit num-
ber. Once the number 999 is reached, no new files can
be created in the folder. If this happens, move the files in
the folder to a different folder.
Set the USB device's write-protect switch to the off
position.
Use a USB device without a security function.
Change the setting so that the recorded data storage
folder is writable.
Use a USB device within this unit's rated current (such
as a hard disk driven by an AC adapter or other external
power supply).
Perform the recording operation on this unit to create
playable files before playing them.
Unplug this unit's power cord from the power outlet.
mum allowable current is detected in this unit's USB port, the
[USB STOP] indicator flashes 5 times, the power supply to the
USB device is cut off, and communications with the USB device
are interrupted. To restore normal operation, disconnect the USB
device from this unit, then press [USB STOP]. Avoid reusing USB
devices for which an excess current has been detected. If normal
operation is not restored (if communications cannot be estab-
lished) after the above procedure is performed, try turning off this
unit's power then turning it back on.
mance may not be achieved.
Files in 16-bit non-compressed PCM format with a sam-
pling frequency of 44.1 kHz are supported.
.WAV or .wav
15
En