Fein ASCD12-100W4 Manual De Instrucciones página 22

OBJ_BUCH-0000000270-003.book Page 22 Monday, February 25, 2019 10:56 AM
en
22
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Operating Instructions.
Adjust the rotation selector switch only when the
machine is at a complete stop.
Thermal overload of the power tool is indicated
through flashing of the LED in the handle.
In case of overload, the machine switches off.
To avoid accidental starting, e. g., during transport, set
the rotation selector switch to the centre position.
Apply the power tool to the nut or screw only when
switched off, as a rotating application tool could slip off.
An unnecessary long impact period increases the wear
of the power tool.
Determine the impact duration for the respective
screwdriving application and check the actually reached
tightening torque with a torque wrench.
Orientation values for the impact duration are shown in
the diagram on page 13.
Recommendations for impact wrench adjustment by
screw size:
ASCD18-300W2 (**)
Setting M [Nm] Screw/bolt Ø Property class
max
6 290 ≥ M 18
5 210 ≥ M 16
4 135 ≥ M 14
3 85 ≥ M 12
2 50 ≥ M 10
1 25 ≥ M 8
ASCD12-150W8 (**)
Setting M [Nm] Screw/bolt Ø Property class
max
6 135 ≥ M 14
5 85 ≥ M 12
4 50 ≥ M 10
3 25 ≥ M 8
2 10 ≥ M 6
1 6 ≥ M 5
Handling the battery.
Store, operate and charge the battery only using FEIN
battery chargers within the battery operating-tempera-
ture range between 5 °C – 45 °C (41 °F – 113 °F). At
the beginning of the charging procedure, the battery
temperature must be within the battery operating-tem-
perature range.
LED indica- Meaning
tor
1 – 4 green Percentage of
LED charge condi-
tion
LED indica-
tor
Continu-
ous red
light
Red flash-
ing light
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor
prior to the battery being deep discharged.
Repair and customer service.
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
If required, you can change the following parts your-
≥ 8.8
self:
≥ 8.8
Application tools, battery, belt hook, bit garage
≥ 8.8
Warranty and liability.
≥ 8.8
The warranty for the product is valid in accordance
≥ 8.8
with the legal regulations in the country where it is mar-
≥ 8.8 keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
≥ 8.8
≥ 8.8
Declaration of conformity.
≥ 8.8
FEIN declares itself solely responsible for this product
≥ 8.8
conforming with the relevant provisions given on the
last page of this Instruction Manual.
≥ 8.8
Technical documents at: C. & E. Fein GmbH, C-D1_IA,
≥ 8.8
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insu-
late the terminals with tape as a protective measure
against short-circuiting.
Activity
Operation
Meaning Activity
Battery is Charge battery
almost empty
Battery is not Bring the battery into
ready for the battery operating-
operation temperature range,
then charge
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power