Fein ASCT18 Manual De Instrucciones página 18

OBJ_BUCH-0000000374-001.book Page 18 Friday, January 24, 2020 9:46 AM
en
18
Follow the safety warnings in the operating instructions
of the battery charger.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 62841 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure level
over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the oper-
ator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organi-
sation of work patterns.
Operating Instructions.
Adjust the rotation selector switch only when the
machine is at a complete stop.
To avoid accidental starting, e. g., during transport, set
the rotation selector switch to the centre position.
When overheated, the machine runs with short, low-
power impulses. Allow the machine to cool down at
no-load speed.
ASCT18/ASCT18M: The screwdriving applications are to
be carried out with mounted depth stop.
ASCT18M/ASCT18UM: The collated cartridge may only
be operated in "clockwise-rotation direction" position.
Setting the torque (ASCT18U/ASCT18UM)
(see page 7).
The factory setting is for the small to mid-size screw
range.
The tightening torque also depends on the force with
which the power tool is pressed against the screw.
Handling the battery.
Store, operate and charge the battery only using FEIN
battery chargers within the battery operating-tempera-
ture range between 5 °C – 45 °C (41 °F – 113 °F). At
the beginning of the charging procedure, the battery
temperature must be within the battery operating-tem-
perature range.
LED indica- Meaning
tor
1 – 4 green Percentage of
LED charge condi-
tion
Continu- Battery is
ous red almost empty
light
LED indica-
tor
Red flash-
ing light
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor
prior to the battery being deep discharged.
Repair and customer service.
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
If required, you can change the following parts your-
self: Application tools, depth stop, battery, belt clip,
magazine
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insu-
Activity
late the terminals with tape as a protective measure
against short-circuiting.
Operation
Charge battery
Meaning Activity
Battery is not Bring the battery into
ready for the battery operating-
operation temperature range,
then charge
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power