EINHELL BG-EM 1846 SE Manual De Instrucciones página 15

Anleitung_BG_EM_1846_SE_SPK7:_
points, plugs and socket couplers for kinks.
6. Operation
Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data. Connect the mains lead
(Fig. 1/Item 5) to an extension cable. It is imperative
to secure the extension cable with the cable grip as
shown in Figure 12.
Important!
To prevent the machine switching on accidentally,
the lawn mower is equipped with a safety switch (Fig.
11/Item A) which must be pressed before the ON
switch (Fig. 11/Item B) can be activated. The lawn
mower switches itself off when the switch is
released.
Repeat this process several times so that you are
sure that the machine functions properly. Before you
perform any repair or maintenance work on the
machine, ensure that the blade is not rotating and
that the power supply is disconnected.
Important. Never open the discharge flap if the
grass box is being emptied and the motor is still
running. The rotating blade can cause serious
injuries.
Always secure the discharge flap and grass bag
carefully. Always switch off the motor before you
remove these items.
The safety distance between the blade casing and
the user provided by the guide struts must be
maintained at all times. Take special care when
mowing and changing direction on embankments
and slopes. Ensure that you have a secure surface
to stand on, wear shoes with anti-slip soles that offer
good grip, and long trousers.
Always mow across the slope (not in up or down
direction). Do not use the mower on gradients
exceeding 15° for safety reasons.
Take special care when moving backwards and
pulling the lawn mower. Danger of stumbling.
Information on correct mowing
We recommend that you mow in overlapping lines.
Only mow with sharp, perfect blades so that the
blades of grass do not fray, making the lawn turn
yellow.
25.09.2008 13:27 Uhr Seite 15
To achieve a good cut, guide the lawn mower in lines
that are as straight as possible. These lines should
always overlap by a few centimeters so that you do
not leave any strips.
How often you should mow the lawn depends on
how fast the lawn grows. During the main growth
period (May – June), mow it twice a week, and once
a week at other times. The cutting height should be
between 4 and 6 cm and the growth before the next
cut should be between 4 and 5 cm. If the lawn grows
longer than this on occasion, do not make the
mistake of cutting to normal length straight away
since this will damage the lawn. Never cut the grass
by more than half its height.
Keep the underside of the mower casing clean and
remove all grass deposits from it. Deposits make it
more difficult to start the mower and also adversely
affect the mowing quality and the grass discharge.
On slopes mow across the slope (not in up or down
direction). You can counteract the tendency of the
mower to slide down the slope by setting it at an
angle upwards.
Select the cutting height to suit the actual length of
the grass. Make several passes to ensure that you
do not remove more than 4 cm of grass length in any
one pass.
Switch off the motor before you carry out any
inspections of the blade. Remember than the blade
will continue to turn for a few seconds after the motor
has been switched off. Never attempt to stop the
blade. Check regularly that the blade is correctly
secured, in good condition and well ground. If not,
grind or replace the blade. If the moving blade strikes
an object, stop the mower and wait until the blade
has come to a complete standstill. Then check the
condition of the blade and the blade holder. If they
are damaged, they must be replaced.
Place the mains lead in loops on the ground in front
of the socket. Mow away from the socket and cable
and ensure that the mains lead is always on the
section of lawn that you have already mowed so that
you do not run over the mains lead with the mower.
As soon as you see mown grass on the lawn whilst
you are mowing, the grass bag will need emptying.
Important. Before you remove the grass bag
switch off the motor and wait until the cutting
tool reaches a standstill.
GB
15