Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Replacing The Blade - EINHELL BG-EM 1846 SE Manual De Instrucciones

Anleitung_BG_EM_1846_SE_SPK7:_
GB
To remove the grass bag, raise the discharge flap
with one hand and remove the grass bag using its
handle with your other hand.
To maintain safety, the discharge flap will close when
you remove the grass back to seal the rear discharge
opening. If any grass residues are caught in the
opening, it is a good idea to pull the mower
backwards around 1 m to make it easier to start the
motor.
Do not remove grass cuttings in the mower casing or
on the cutter by hand or with your feet. Instead use
suitable tools such as a brush or broom.
To ensure that it can collect the grass correctly the
grass bag and in particular the net must be cleaned
from the inside after use.
Only attach the grass bag after switching off the
motor and the cutting tool has reached a standstill.
Raise the discharge flap with one hand and, holding
the grass bag by its handle in your other hand, attach
it from the top.

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
16
25.09.2008 13:27 Uhr Seite 16
8.2 Servicing
Worn out or damaged blades, blade mounts, and
bolts should be replaced as a set by an
authorized professional in order to keep the
machine in balance.
Do not clean the lawn mower with running water,
particularly with high-pressure water. Ensure that
all mounting components (i.e. screws, bolts, nuts
etc.) are always tightened so that the machine
can be safely operated at all times.
Frequently check the grass catch assembly for
signs of wear.
Replace excessively worn or damaged parts
immediately.
Store your lawn mower in a dry room.
In order to ensure that you enjoy your scarifier
for many years to come, all screwed parts, as
well as the wheels and axles, should be cleaned
and lubricated.
Keeping your hand mower in good condition not
only ensures a long lifespan and high
performance, but also enables the machine to
thoroughly cut your grass with minimal effort. For
best results, clean the lawn mower with a brush
or rag. Do not use any solvents or water to
remove dirt.
The cutting components - i.e. the knife cage and
lower knife blade - are subjected to more wear
and tear than any other component of the unit.
Therefore, routinely check the condition of the
blade and make sure that it is tightly fastened. If
the blade is completely worn out, it must be
immediately replaced or ground sharp again. An
excessively vibrating mower means that the
blade is not properly balanced or has become
deformed from striking an object. In this case,
the blade must be repaired or replaced.
There are no parts inside the equipment which
require additional maintenance.

8.3 Replacing the blade

For safety reasons, we recommend having the blade
replaced by an authorized professional. Important.
Wear work gloves! Only replace the blade with a
genuine Einhell replacement blade, as this will
ensure top performance and safety under all
conditions.
Carry out the following steps to change the blade:
Undo the fastening screw (see Fig. 13a).
Remove the blade and replace with a new one.
When fitting the blade, make sure it is installed in
the right direction. The bladeʼs air vanes must jut
into the motor compartment (see Fig. 14). The
dome mounts must be aligned with the punch
holes in the blade (see Fig. 14).