Sound Setting; Adjusting Bass/Treble/Balance (Between Left And Right)/Fader (Between Front And Rear)/Defeat; Turning Multeq On/Off; Equalizer Presets - Alpine CDA-9887 Manual De Operación

Sound Setting

/ESC
Rotary encoder (AUDIO)
SOURCE/
/ /ENT
FUNC./SETUP
/RTN A. SEL
MultEQ
Adjusting Bass/Treble/Balance (Between
Left and Right)/Fader (Between Front
and Rear)/Defeat
1
Press Rotary encoder (AUDIO) repeatedly to
choose the desired mode.
Each press changes the mode as follows:
1
SUBWOOFER* BASS*
3
FADER* DEFEAT VOLUME
Subwoofer: 0 ~ +15
Bass level: -7~+7
Treble level: -7~+7
Balance: L15 ~ R15
Fader: R15 ~ F15
Defeat: ON/OFF
Volume: 0 ~ 35
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, BALANCE, FADER or DEFEAT
mode, the unit automatically returns to normal mode.
1
* When the subwoofer mode is set to OFF, its level cannot be adjusted.
2
* When the MultEQ is set to OFF, its level cannot be adjusted.
3
* If you set the 4.2ch/2.2ch switch (pages 40 to 42) to 2.2ch, you
cannot adjust the FADER mode.
2
Turn the Rotary encoder (AUDIO) until the
desired sound is obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of
BASS, TREBLE and EQ will return to the factory defaults
and MX (page 19) is turned off.
• Depending on the connected devices, some functions and display
indications do not work.
BAND
Preset buttons
(1 through 6)
2 2
TREBLE* BALANCE
1
SUBWOOFER*

Turning MultEQ on/off

MultEQ, developed by Audyssey Labs, automatically corrects the audio
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this, MultEQ must take
measurements of the vehicles response characteristics. For details on the
set up procedure, consult your authorized Alpine dealer.
Press MultEQ to select ON/OFF mode.
• If MultEQ is turned on and its button pressed and held for at least 2
seconds, the Curve mode is switched (only when curve1 and curve2
are stored).
• When using MultEQ, MX, X-OVER, T.Correction, User's EQ,
Parametric EQ and Graphic EQ are set automatically. They are no
longer user adjustable.
• When an external audio processor is connected, the MultEQ function
cannot be used.

Equalizer Presets

10 typical equalizer settings are preset at the factory for a variety of
musical source material.
1
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
2
Turn the Rotary encoder to select AUDIO mode,
and then press / /ENT.
Bluetooth GENERAL
*
TUNER Bluetooth
* Only when HD Radio/SAT Radio is connected.
3
Turn the Rotary encoder to select Factory's EQ
mode, and then press
4
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press
Flat Pops Rock
Electrical Dance Hip Hop&Rap
Country Classical User1
User4 User5 User6
• By selecting User's 1 to 6, you can recall the stored preset number in
"Adjusting and Storing the Graphic Equalizer Curve" (page 14) or
"Adjusting and Storing the Parametric Equalizer Curve"
(page 14) .
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
• Pressing /RTN during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is canceled.
• This function is inoperable when DEFEAT is set to ON (page 13).
• Press and hold /ESC for at least 2 seconds, the setting mode is
canceled.
AUDIO DISPLAY
/ /ENT.
/ /ENT.
News Jazz&Blues
Easy Listening
User2 User3
13
-EN