Fixture Test; Display Setting - TECshow RAZOR 7R BEAM Manual De Usuario

Off If DMX Off— Lamp turns off when DMX signal is cut off
Select Off If DMX Off, press ENTER button to confirm, present
mode will blink on the display, use UP and DOWN button to
select Yes (Lamp turns off when DMX signal is cut off), press
ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
Ignition Delay—Delay time between power on and lamp on
Select Ignition Delay, press ENTER button to confirm, present
mode will blink on the display, use UP and DOWN button to
adjust the delay time from 0S to 255S, press ENTER button
to store. Press MENU button back to the last menu or let the
unit idle one minute to exit menu mode.
Low Power Delay
Delay time between reduce lamp power and shutter off the
unit Select Low Power Delay, press ENTER button to confirm,
present mode will blink on the display, use UP and DOWN
button to adjust the delay time from 0S to 255S, press ENTER
button to store. Press MENU button back to the last menu or
let the unit idle one minute to exit menu mode. (If you set the
low power delay time to 3S, the lamp will run in half power 3
seconds after the unit shutter off)

Display Setting

Enter menu mode, select Display Setting, press ENTER but-
ton to confirm, use UP and DOWN button to select Display
Inverse, Backlight Auto Off, Backlight Intensity, Temperature
unit or Language.
Display Inverse
Select Display Inverse, press ENTER button to confirm, pres-
ent mode will blink on the display, use UP and DOWN button
to select No (normal display) or Yes (inverse display), press
ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
Backlight Auto Off
Select Backlight Auto Off, press ENTER button to confirm,
present mode will blink on the display, use UP and DOWN
button to select No (display always on) or Yes (display goes
off one minute after exiting menu mode), press ENTER but-
ton to store. Press MENU button back to the last menu or let
the unit idle one minute to exit menu mode.
Backlight Intensity
Select Backlight Intensity, press ENTER button to confirm,
present mode will blink on the display, use UP and DOWN but-
RAZOR 7R BEAM
ENGLISH VERSION
ton to adjust backlight intensity from 1 (dark) to 10 (bright),
press ENTER button to store. Press MENU button back to the
last menu or let the unit idle one minute to exit menu mode.
Temperature Unit
Select Temperature Unit, press ENTER button to confirm,
present mode will blink on the display, use UP and DOWN
button to select °C or °F, press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
Language
Select Language, press ENTER button to confirm, present
mode will blink on the display, use UP and DOWN button to
select English or Chinese, press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one
minute to exit menu mode.

Fixture Test

Enter menu mode, select Fixture Test, press ENTER button
to confirm, use UP and DOWN button to select Auto Test or
Manual Test
Auto Test
Select Auto Test, press ENTER button to confirm, the unit will
run built-in programs to automatically test pan, tilt, color,
gobo, gobo rotation, shutter, dimmer, prism, prism rotation,
frost, focus, and lamp on/off. . Press MENU button back to the
last menu or exit menu mode after auto test.
Manual Test
Select Manual Test, press ENTER button to confirm, the pres-
ent channel will show on the display, use Up and DOWN but-
ton to select channel, press ENTER button to confirm, then
use UP and DOWN button to adjust the value, press ENTER
button to store, the fixture will run as the channel value indi-
cates. Press MENU button back to the last menu or exit menu
mode let the unit idle one minute. (All channels value will be-
come 0 after exiting Manual Test menu)
Fixture Information
Enter menu mode, select Fixture Information, press ENTER
button to confirm, use UP and DOWN button to select Fixture
Use Time, Lamp On Time or Firmware Version.
Fixture Use Time
Select Fixture Use Time, press ENTER button to confirm, fixture
p. 13