TECshow RAZOR 7R BEAM Manual De Usuario página 12

Fixture Setting
Enter menu mode, select Fixture Setting, press ENTER button
to confirm, use UP and DOWN button to select Pan Inverse,
Tile Inverse, BL.O. P/T Moving, BL.O. Color Change or BL.O.
Gobo Change.
Pan Inverse
Select Pan Inverse, press ENTER button to confirm, present
mode will blink on the display, use UP and DOWN button to
select No (normal) or Yes (pan inverse), press ENTER button
to store. Press MENU button back to the last menu or let the
unit idle one minute to exit menu mode.
Tilt Inverse
Select Tilt Inverse, press ENTER button to confirm, present
mode will blink on the display, use UP and DOWN button to
select No (normal) or Yes (tilt inverse), press ENTER button
to store. Press MENU button back to the last menu or let the
unit idle one minute to exit menu mode.
P/T Feedback — pan/tilt Feedback
Select P/T Feedback, press ENTER button to confirm, pres-
ent mode will blink on the display, press UP/DOWN button
to select No (Pan or tilt's position will not feedback while out
of step.) or Yes (Feedback while pan/tilt out of step. ), press
ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
BL.O. P/T Moving—Blackout while pan/tilt moving
Select BL.O. P/T Moving, Press ENTER button to confirm, pres-
ent mode will blink on the display, use UP and DOWN button
to select No (normal while pan/tilt moving) or Yes (blackout
while pan/tilt moving), press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
BL.O. Color Change—Blackout while change color
Select BL.O. Color Change, press ENTER button to confirm,
present mode will blink on the display, use UP and DOWN
button to select No (normal while change color) or Yes (black-
out while change color), press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one
minute to exit menu mode.
BL.O. Gobo Change—Blackout while change gobo
Select BL.O. Gobo Change, press ENTER button to confirm,
present mode will blink on the display, use UP and DOWN
button to select No (normal while changing gobo) or Yes
RAZOR 7R BEAM
ENGLISH VERSION
(blackout while changing gobo), press ENTER button to store.
Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
Lamp Setting
Attention: The lamp will not be on unit detected temperature
is lower than 45°C.
Enter menu mode, select Fixture Setting, press ENTER button
to confirm, use UP and DOWN button to select On/Off, State/
Power on, Off Via DMX, On if DMX on, Off if DMX off, Cooling
Mode, Ignition Delay or Low Power Delay.
On/Off—Turn on/off the lamp
Select On/Off, press ENTER button to confirm, present mode
will blink on the display, use UP and DOWN button to select
On (lamp on) or Off (lamp off), press ENTER button to store.
Press MENU button back to the last menu or let the unit idle
one minute to exit menu mode.
State/Power On—Lamp state while power on
Select State/Power On, press ENTER button to confirm, pres-
ent mode will blink on the display, use UP and DOWN button
to select On (Lamp on while power on) or Off (Lamp off while
power on), press ENTER button to store. Press MENU button
back to the last menu or let the unit idle one minute to exit
menu mode.
Off Via DMX—Turn off the unit via DMX controller
Select Off Via DMX, press ENTER button to confirm, present
mode will blink on the display, use UP and DOWN button to
select Yes (turn off the unit via DMX controller available) or
No (turn off the unit via DMX controller impracticable), press
ENTER button to store. Press MENU button back to the last
menu or let the unit idle one minute to exit menu mode.
(When you operate the unit via DMX controller, set the value
of channel "special function" to "lamp off", waiting for 5 sec-
onds, then the lamp will be off if you choose "yes" mode).
On If DMX On— Lamp turns on when DMX signal is detected
Select On If DMX On, press ENTER button to confirm, present
mode will blink on the display, use UP and DOWN button to
select Yes (Lamp turns on when DMX signal is detected) or No
(keep the present state), press ENTER button to store. Press
MENU button back to the last menu or let the unit idle one
minute to exit menu mode (If the lamp is off via DMX signal,
you can reconnect the DMX controller to make the lamp on).
p. 12