When The Work Is Done - Bosch BSG8 Serie Instrucciones De Uso

Caution!
Floor tools are subject to a certain amount of wear,
depending on the type of hard floors you have
(e.g. rough, rustic tiles). Therefore, you must check
the underside of the floor tool at regular intervals.
Worn undersides of floor tools may have sharp edges
that can damage sensitive hard floors, such as parquet
or linoleum. The manufacturer does not accept any
responsibility for damage caused by worn floor tools.
Vacuuming with accessories
10
Figure
Remove the combination tool upwards
out of the accessory holder.
a) Crevice nozzle
For vacuuming in crevices and corners.
For difficult-to-reach places, the combination tool
can be extended in two stages by pulling out the
crevice nozzle like a telescope.
Pull out the crevice nozzle in two stages until it audi-
bly clicks into place.
The crevice nozzle can be pushed back together by
releasing the telescopic locks (press in the direction
of the arrow).
b)Upholstery nozzle
For cleaning upholstered furniture, curtains, etc.
c) Hard furnishings brush
For window frames, cabinets, profiles, etc.
Fold up the upholstery nozzle in the direction of the
arrow.
The brush ring is extended by turning in the direc-
tion of the arrow.
The brush ring must be turned back in and the
upholstery nozzle folded back up before the combi-
nation tool is inserted into the accessory holder.
11*
Figure
Mattress nozzle
For vacuuming mattresses, upholstery etc.
(attach to handle or suction pipe as required).
12*
Figure
Pet hair upholstery nozzle
For easy and thorough removal of pet hair (attach to
handle or suction pipe as required).
To clean the pet hair upholstery nozzle, simply vacuum
using the handle.
If it is very dirty, the pet hair upholstery nozzle can also
be opened.
To do this, turn the two screws on the sides of the nozzle
(e.g. using a coin) and remove the inner part from the
nozzle.
After cleaning, replace the inner part (make sure it is
correctly seated) and screw to the housing.
* Dependent on model
13*
Figure
Pet hair tool
Floor tool for easy and thorough vacuuming of pet hair.
Push the telescopic tube into the connecting piece of the
pet hair tool until it engages.
Press on the locking collar and pull out the telescopic
tube to disconnect.
To clean, simply vacuum the tool using the suction
pipe/handle.
14*
Figure
Hard-floor brush
For vacuuming hard floor coverings (tiles, parquet floor-
ing, etc.)
Push the telescopic tube into the connecting piece of
the hard-floor brush until it engages.
Press on the unlatching sleeve and pull out the telescop-
ic tube to disconnect.
15
Figure
You can use the parking aid on the back of the vacuum
cleaner if you wish to stop vacuuming for a short time.
Slide the plastic lug on the tool connector into the
groove at the back of the vacuum cleaner.

When the work is done

16
Figure
Switch the vacuum cleaner off and unplug the power
cord from the mains.
Tug the power cord and let go. The cable then rewinds
automatically.
To reactivate or deactivate the cable brake, quickly tug
the power cord.
17
Figure
To store or transport the vacuum cleaner, use the stor-
age aid on the underside of the vacuum cleaner. Stand
the vacuum cleaner up on its end. Slide the plastic lug
on the floor tool into the groove on the underside of the
unit.
Changing the dust bag and filters
Replacing the dust bag
18
Figure
If the dust bag change indicator lights up brightly and
evenly when the floor tool is lifted from the carpet and
the highest suction power is selected, the dust bag must
be changed, even though it may not yet be full. In this
case it is essential to change the dust bag due to the
type of material it contains.
Open the dust bag compartment lid by moving the dust
compartment locking lever in the direction of the arrow.
19
Figure
Seal the dust bag by pulling the self-seal tap and then
remove it.
11