Operating Conditions; Fault Conditions; Start Charging - Webasto Live Instrucciones De Uso

7.1.1

Operating conditions

See also Fig. 8
Operating Description
indicator
When the charging station is switched on,
N1
this lights up red for 30 s, then flashes red-
green-blue at one-second intervals. A beep
sounds if the start-up process is successful.
N2 LED is blue:
Charging station in standby mode; char-
ging station can be used.
LED is green:
N3
Charging station being used; charging
vehicle.
N4 LED flashes blue at 1 second intervals:
Charging coupling connected to the
vehicle, authentication has not been car-
ried out yet.
LED flashes green at 1 second intervals:
N6
Charging cycle paused by the vehicle
(indicator in configuration can be activated)
7.1.2

Fault conditions

See also Fig. 9
Fault list Description
LED is yellow for 1 s and green for 2 s:
F1
The charging station has become hot and
charges the vehicle with reduced power. After
a cool-down phase the charging station con-
tinues the normal charging cycle.
F2 LED is yellow and an acoustic signal sounds
for 0.5 s:
Excess temperature. Charging stopped due to
high temperature within the charging station.
After a cool-down phase the charging station
continues the normal charging cycle.
LED is red and an acoustic signal sounds for
F3
0.5 s and then for 5 s following a pause:
There is a problem in the voltage or system
monitoring.
5110326C_OI-II_Webasto Live Multilanguage
DANGER
Danger of fatal electric shock.
Switch off and secure the power supply to the
u
charging station. Only then unplug the cable from
the vehicle.
Contact the Webasto Charging Hotline at
u
00800-24274464.
Fault list Description
LED flashes red for 1 s at 2 s intervals and an
F5
acoustic signal sounds for 0.5 s and then for
5 s following a pause:
There is a fault in the vehicle.
Re-connect the vehicle
u
u If the warning persists, contact the car cus-
tomer service.
F6 LED flashes red 2 times, followed by a brief
pause and a buzzer sounds for 0.5 s:
The supply voltage is outside the valid range
of 180 V to 270 V.
u Checking by an authorised electrician.
LED flashes red 3 times, followed by a brief
F7
pause and a buzzer sounds for 0.5 s:
There is a fault in the installation. Info for in-
staller.
7.1.3 Communication statuses
See also Fig. 10
Operating Description
indicator
LED is blue at 0.5 second intervals:
C1
The authorisation process is in progress.
C2 LED lights up red for 1.5 / 1 / 0.5 s and a
beep sounds at the same time:
Restart of the charging station by RFID
dongle owner/operator (indicator in config-
uration can be activated)
LED lights up red for 0.5 s at 60-second in-
C3
tervals:
Information about lost GSM signal (every 60
s in all modes) (indicator in configuration
can be activated)
Operating Description
indicator
C5 LED flashes blue for 0.5 s and red for 0.5 s:
RFID dongle is not permitted by service
provider or charging station.
LED flashes blue for 1 s and green for 1 s
C6
and a beep sounds:
Authorisation was successful. The vehicle
must be connected to the charging station
within 45 s (default value).
C7 LED flashes green at 0.5 second intervals:
Increasing state of charge (SOC) with avail-
able connection using ISO 15118, 12.5%
SOC per LED, increasing steadily periodic-
ally.
LED is purple for 4 s and an acoustic signal
C8
sounds for 1.5 - 1 - 0.5 s:
Reset by backend.
7.2

Start charging

NOTE
Always take into account the vehicle requirements before
charging a vehicle.
NOTE
Park the vehicle for charging such as to avoid strain in the
charging cable.
See also Fig. 11
The RFID dongle can be authorised before or after the
charging cable is plugged into the vehicle. Note that the
time between authorisation and connection of the char-
ging cable is limited to 45 s (default value). After this
period, the authorisation is no longer valid, and the
charging station returns to the starting state.
Action Description
The user is enabled.
u Hold the RFID
dongle to the
card reader
u Connect the Charging station performs system
charging and connection tests.
coupling to LED is blue then switches to green:
the vehicle. Charging mode
EN
31