Bosch GCM 350-254 Professional Manual Original página 31

OBJ_BUCH-2953-001.book Page 31 Wednesday, December 21, 2016 3:02 PM
 The power tool is provided with a laser warning label
(marked with number 33 in the representation of the
power tool on the graphics page).
DO NOT EXPOSE USERS OF
TELESCOPIC OPTICS
CLASS 1M LASER PRODUCT
Do not direct the laser beam at persons
or animals and do not stare into the di-
rect or reflected laser beam yourself, not
even from a distance. You could blind
somebody, cause accidents or damage
your eyes.
 If laser radiation strikes your eye, you must deliberate-
ly close your eyes and immediately turn your head
away from the beam.
 Do not use any optical instruments such as binoculars
to view the radiation source. Doing so can damage your
eye.
 Do not direct the laser beam at persons who are looking
through binoculars or similar instruments. Doing so can
damage their eye.
 Do not make any modifications to the laser equipment.
The setting options described in these operating instruc-
tions can be used safely.
 Keep your workplace clean. Blends of materials are par-
ticularly dangerous. Dust from light alloys can burn or ex-
plode.
 Do not use dull, cracked, bent or damaged saw blades.
Unsharpened or improperly set saw blades produce nar-
row kerf causing excessive friction, blade binding and kick-
back.
 Do not use high speed steel (HSS) saw blades. Such saw
blades can easily break.
 Always use blades with correct size and shape (dia-
mond versus round) of arbour holes. Blades that do not
match the mounting hardware of the saw will run eccentri-
cally, causing loss of control.
 Do not replace the installed laser with another laser
type. A laser that is not compatible with this power tool
could pose a risk to persons.
 Never remove cutting remainders, wood chips, etc.
from the sawing area while the machine is running. Al-
ways guide the tool arm back to the neutral position first
and then switch the machine off.
 Do not touch the saw blade after working before it has
cooled. The saw blade becomes very hot while working.
 Never make warning signs on the machine unrecognis-
able.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
Bosch Power Tools
IEC 60825-1:2014
<0.39mW, 650 nm
LASER RADIATION
Symbols
The following symbols can be important for the operation of
your power tool. Please memorise the symbols and their
meanings. The correct interpretation of the symbols helps
you operate the power tool better and more safely.
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Symbols and their meaning
 Laser radiation
Do not expose users of telescopic
optics
Class 1M laser product
 Keep hands away from the cutting
area while the machine is running.
Danger of injury when coming in con-
tact with the saw blade.
 Wear a dust respirator.
 Wear safety goggles.
 Wear ear protectors. Exposure to
noise can cause hearing loss.
 Danger area! Keep hands, fingers or
arms away from this area.
English | 31
The table shows the rec-
ommended speed setting
depending on the materi-
al to be worked: alumini-
um, plastic, wood.
(not available for all coun-
try-specific product ver-
sions)
1 609 92A 39K | (21.12.16)