OBJ_BUCH-2953-001.book Page 40 Wednesday, December 21, 2016 3:02 PM
40 | English
Adjusting: (see figure W2)
– Loosen all four set screws 68 with the hex key (4 mm) 37
and turn the saw table 18 together with the scale 26 until
the leg of the angle gauge is flush with the saw blade over
the complete length.
– Retighten the screws again.
When the angle indicator 24 is not in line with the 0° mark of
scale 26 after adjusting, loosen screw 69 with a cross-head
screwdriver and align the angle indicator alongside the
0° mark.
Transport (see figure X)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw 6 if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Make sure that the depth stop 40 is swung completely
backward and that the adjusting screw 39 fits through the
recess without touching the depth stop when moving the
tool arm.
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Wind up the mains cable and tie it together with Velcro
strap 70.
– Carry the machine by the transport handle 10 or hold it by
the recessed handles 28 on the sides of the saw table.
When transporting the power tool, use only the trans-
port devices and never use the protective devices.
The power tool should always be carried by two per-
sons in order to avoid back injuries.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning
For safe and proper working, always keep the power tool and
its ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Clean the roller 16 regularly.
1 609 92A 39K | (21.12.16)
Measures for Noise Reduction
Measures on behalf of the manufacturer:
– Soft starting
– Delivery of the machine with a saw blade developed partic-
ularly for noise reduction
Measures on behalf of the user:
– Low-vibration assembly on a firm working surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of saw blade and power tool
Accessories
Quick-action clamp
Insert plates
Dust bag
Material stop
Lock screw of the material stop
Saw blades for wood and plate materials, panels and
strips/mouldings
Saw blade 254 x 30 mm, 60 teeth
Saw blades for plastic and non-ferrous metals
Saw blade 254 x 30 mm, 80 teeth
Saw blades for all types of laminate flooring
Saw blade 254 x 30 mm, 84 teeth
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Article number
1 609 B02 585
1 609 B05 128
1 609 B05 010
1 609 B02 365
1 609 B00 263
2 608 642 530
2 608 642 528
2 608 642 135
Bosch Power Tools