ELECTRONIC SELECTING RPM (GL040E-GL080E)
The rpm can be adjusted by rotating the wheel (14). The choice of speed
depends on the characteristics of the abrasive disc and the material to
be worked.
DISASSEMBLING AND REPLACING THE GRINDING WHEEL OR
DISC-HOLDER
This operation can be performed in two ways.
- First method: lock the spindle shaft (4) by pressing the button (3) and
simultaneously turning the grinding wheel until it comes to a stop.
Loosen the ring nut (10-10A) with the adjustable wrench (12), replace
the grinding wheel or fiber disc, then tighten firmly. Loosen the
spindle shaft by releasing the button and manually turn the grinding
wheel or disc-holder to verify that it has locked in place.
WARNING: remember to press the spindle shaft locking button only
after the tool has come to a complete stop to avoid breaking the
gearbox or the push-button pin and invalidating the warranty.
- Second method: to lock the spindle shaft (4) insert the 17 mm wrench
(12) into the slot of the spindle shaft, between the grinding wheel or
disc-holder and the gear box. Loosen the ring nut with the adjustable
wrench, replace the grinding wheel or fiber disc, then tighten firmly.
Tools other than those mentioned must not be used for slackening
for tightening purposes.
USABLE ABRASIVE WHEELS
GL080-GL080E
Ø
125
mm depressed centre type abrasive wheels.
GL040-GL040E
- Ø 115 mm fiber disc
MAINTENANCE
All maintenance operations are carried out with the power supply
disconnected. At the end of each work session, or when required, remo-
ve any dust from the body of the tool using a jet of compressed air,
paying particular attention to the motor ventilation slots.
No other maintenance operations must be undertaken by the user.
Maintenance and cleaning of the inner parts, like brushes, ball
bearings, gears etc. or others, must be carried out only by an
authorised customer-service workshop.
10
ELECTRIC SAFETY - LOW TENSION
The tests have been carried out in accordance with the standard:
EN 60745-1 safety of hand-held electric motor operated tools
EN 50144-2-3 particular requirements for grinders.
RADIO SUPPRESSION
The tools are suppressed in accordance for the prevention and elimina-
tion of radio disturbances measured in accordance with standard:
EN55014-1+EN55014-2; EN61000-3-2+EN61000-3-3.
NOISE
The noise level, produced by the machine in normal working conditions
at the work station is 88,7 dB measured according to regulation
3744 + UNI EN ISO 11203.
Warning: wear suitable hearing protections! (see warnings).
MEAN ACCELERATION VALUE
The mean quadratic acceleration value is less than 2,5 m/sec
in accordance with standard UNI EN 28662
GUARANTEE
All tools manufactured by RUPES Spa are guaranteed for 12 months
from the date of purchase against fabrication and material defects. All
tools must be used only with RUPES original accessories and spare
parts: we refuse all responsibility for damages or accidents caused by
non-observance of this rule which will also cause the termination of the
guarantee. The guarantee will no longer be valid if the instructions con-
tained in this booklet are not followed, if the tool is used for purposes
other than that for which it is intended, if it is dismantled, interfered with in
any way or damaged due to neglect. The guarantee will be made valid
by filling-in the form on the inside back cover of this instruction
booklet. If the tool is found to be defective or malfunctions, it should be
returned carriage free in one piece in its original packing together with
the guarantee certificate to the manufacturer or to one of the Assistance
Centres listed in the appendix to this booklet. The guarantee does not
automatically imply replacement of the tool. RUPES Spa reserves the ri-
ght to make any technical or design modification to its products without
prior notice. The manufacturer is not liable for any print errors. This docu-
ment voids and replaces previous ones.
EN ISO
2
measured
+ UNI EN ISO 5349.