Changing Settings - Clarion DXZ948RMP Manual De Instrucciones

5.1ch Surround Decoder Operations
4. Touch on the DSF menu No. to select
the desired DSF menu.
DSF MODE
RTN
CHURCH BASIC
ON 1
DSF menus
HALL CHURCH STADIUM LIVE
JAZZCLUB THEATER HALL...
No. Function Discription
Name
1 HALL Large concert hall
2 CHURCH Church with a vaulted
ceiling
3 STADIUM Large stadium without
roof or walls
4 LIVE Live performance hall,
larger than a jazz club
5 JAZZCLUB Jazz club with a low
ceiling
6 THEATER Movie or drama theater
5. Press the [SOUND] button to return to the
original mode.
Selecting the Parametric
Equalizer menu
Parametric Equalizer (P.EQ) allows you to
compensate the entire frequency level range in
detail by smooth curve using frequency
compensation matched to the type of your car.
• The factory default setting provides the
following settings for all speakers.
FREQ = 1kHz, Q =1, GAIN = 0dB
1. Press the [SOUND] button.
2. Touch P.EQ.
OFF OFF OFF
Dolby PL II
DSF P. EQ
RTN
SOUND MENU
A - MODE
3. Touch on the ON/OFF display.
The P.EQ effect is toggled ON/OFF.
P.EQ MODE
RTN
SIGNAL
P-NOIS
OFF
When the P.EQ effect is set to "OFF", the
62
DXZ948RMP
P.EQ setting is not reflected on the music
source. This ends the P.EQ setting. Press
the [SOUND] button to return to the original
mode.
4. Touch on the P.EQ menu No. to select
the P.EQ menu.
P.EQ MODE
RTN
SP - SEL
FRONT
ON
P.EQ menus
SIGNAL SP-SEL BAND FREQ
GAIN SIGNAL...
5. Touch on the right on the display and
adjust the item as desired.
SIGNAL (selects the adjustment signal):
Selects "P-NOIS" or "MUSIC"
• P-NOIS: set when pink noise is to be
used
• MUSIC: set to use music signals
SP-SEL (selects the speakers whose P.EQ
value is to be adjusted):
Select one of "FRONT", "CENTER" or
"SURROUND".
• FRONT: front speaker
• CENTER: centre speaker
• SURROUND: surround speaker
BAND (selects the frequency band):
Select one of band 1 to 3
FREQ (selects the centre frequency):
The adjustment range is from 20 Hz to
20 kHz.
Q (sets the Q curve):
Sets one of 1, 3, 5, 7, or 20 as the
sharpness of the Q curve.
GAIN (adjusts the output level):
Adjusts the gain (output level) within the
range -12dB to +12dB. (1dB steps, 25
points)
6. Repeat steps 4 and 5 to adjust the desired
item.
7. Press the [SOUND] button to return to the
original mode.
P. EQ adjustment
The settings that can be adjusted in the P.EQ
menu are as follows. The centre frequency, gain
and Q curve can be stored to channel/band
combinations.
For example, centre frequency "250Hz", gain "
-8dB" and Q curve "3" can be stored to band 1
on the front.
For details on the P.EQ function, see "P. EQ
adjustment" (cf. page 21).

Changing settings

When a 5.1ch surround decoder is connected,
settings relating to music in the adjust mode are
changed.
Selecting setting items
The following describes the items whose
settings are changed.
For details of other items that are not changed,
see "Changing settings" (cf. Page 39) at
"Operations Common to Each Mode".
1. Press the [A] button.
Q
The mode changes to the adjust mode.
ADJUST MODE
CENTER - SP
SOUND
Setting items
Main Item
SOUND CENTER-SP / SRD-SP / SUB-WOOFER
• Setting the speaker ON/OFF (cf. page 64)
FRONT HPF / CENTER HPF / SRD HPF / SUB-W LPF
• Adjusting the speaker filter frequency (cf. Page 64)
SP GAIN
• Adjusting the speaker output level (cf. page 46)
DELAY CENTER-SP / SRD-SP
• Adjusting the speaker delay time (cf. page 65)
DOLBY D D-RANGE
• Adjusting the dynamic range (cf. page 65)
PL II CONT PANORAMA / DIMENSION / CTR WIDTH
• Setting the music mode in detail (cf. page 47)
5.1ch Surround Decoder Operations
2. Touch on the setting item display to
select the item to set.
∗ Touching
on the left of the display
switches main items 1 item at a time.
Touching on the left of the display
switches sub-items continuously.
∗ Touching
on the centre of the
display switches the sub-items 1 item at a
time. Touching switches sub-items
continuously.
3. When "THROUGH" is displayed at the right
of the display, touch THROUGH to switch to
the adjustment details display.
4. Either touch on the right of the
display, or turn the [ROTARY] knob to set
the details.
ON
To return to the original mode
1. Press the [A] button again.
Sub-item
63
DXZ948RMP