Clarion DXZ948RMP Manual De Instrucciones página 24

Operations Common to Each Mode
3. Either touch on the right of the
display, or turn the [ROTARY] knob to select
"ON" or "OFF".
4. Press the [A] button to return to the original
mode.
Setting the beep for when
buttons are operated (BEEP)
The short or long high-pitched tone you hear
when a button is operated is called a "BEEP".
• The factory default setting is "ON".
1. Press the [A] button to set to the adjust
mode.
2. Touch on the setting item display to
select "BEEP" under "APPERNCE".
ADJUST MODE
BEEP ON
APPERNCE
3. Either touch on the right of the
display, or turn the [ROTARY] knob to select
"ON" or "OFF".
4. Press the [A] button to return to the original
mode.
Selecting each mode
This item cannot be selected when the Dolby
Pro Logic II is set to "MUSIC" or "MATRIX" (cf.
page 17).
• The factory default setting is "PRO" for AC-
PRO III and "P.EQ" for EQ SELECT.
AC-PROIII
When "STD" (standard mode) is selected, the
sound quality and field can be adjusted by VSE
(Virtual Space Enhancer) so that the same
audio effect can be obtained whichever seat you
are sitting in.
When "PRO" (PRO mode) is selected, the
sound quality and field can be adjusted in detail
for each seating position.
44
DXZ948RMP
EQ SELECT
When "P.EQ" (equalizer mode) is selected, the
entire frequency level range can be
compensated by a detailed smooth curve.
When "BAS / TREB" (bass / treble mode) is
selected, the frequency level can be
compensated by dividing it into 2 major levels,
bass (low tones) and treble (high tones).
1. Press the [A] button to set to the adjust
mode.
2. Touch on the setting item display to
select "AC-PRO III" under "SOUND" and
"EQ SELECT" under "SOUND".
ADJUST MODE
AC - PRO III PRO
SOUND
3. Either touch on the right of the
display, or turn the [ROTARY] knob to select
the mode.
Mode selection
AC-PRO III STD
• Standard mode (VSE menu)
PRO
• PRO mode (position menu)
EQ SELECT P.EQ
• Equalizer mode (P.EQ menu)
BAS / TREB
• Bass / treble mode
4. Press the [A] button to return to the original
mode.
Setting the speaker
configuration (SP-SETTING)
Set to match the speaker configuration of your
car to fully bring out the audio characteristics of
this unit.
• The factory default setting is "SW L + SW R
1. Press the [A] button to set to the adjust
mode.
2. Touch on the setting item display to
select "SP-SETTING" under "SOUND".
ADJUST MODE
SP - SETTING SW L +SW R
SOUND
3. Either touch on the right of the
display, or turn the [ROTARY] knob to set
the speaker configuration.
Speaker configuration
CTR+SW Front/rear speakers (4ch)
5.1ch Centre speaker (1ch)
configuration Sub-woofer (1ch)
SW L +SW R Front/rear speakers (4ch)
4ch+sub-woofer Sub-woofer (2ch)
configuration
Notes:
• Sound is not output from the centre speaker
unless the following settings are made when
"CTR+SW" is set.
(1) Referring to "Selecting the PLII menu
(Dolby PL II)" (cf. page 17), set the Dolby Pro
Logic II mode to "MUSIC" or "MATRIX".
(2) Referring to "Setting speakers ON/OFF
(CENTER-SP/SUB-WOOFER)" (cf. page 45),
set the centre speaker to "ON".
• Sound is not output from the sub-woofer Lch
L R
when "SW +SW " is set and the Dolby Pro
Logic II mode is set to "MUSIC" or "MATRIX".
4. Press the [A] button to return to the original
mode.
Setting speakers ON/OFF
(CENTER-SP/SUB-WOOFER)
Set the centre speaker (CENTER-SP) and sub-
woofer (SUB-WOOFER) ON/OFF.
Be sure to set this setting to "OFF" when there
is no centre speaker or sub-woofer.
• The centre speaker (CENTER-SP) can be set
when the Dolby Pro Logic II mode is set to
"MUSIC" or "MATRIX", and "SP-SETTING" is
set to "CTR-SW".
• The factory default setting is "ON".
1. Press the [A] button to set to the adjust
mode.
2. Touch on the setting item display to
".
select "CENTER-SP" under "SOUND" and
"SUB-WOOFER" under "SOUND".
ADJUST MODE
CENTER - SP
SOUND
Operations Common to Each Mode
3. Either touch on the right of the
display, or turn the [ROTARY] knob to select
"ON" or "OFF".
4. Press the [A] button to return to the original
mode.
Adjusting the filter
frequencies of speakers
(HPF/SUB-W LPF)
This function allows you to adjust the filter
frequency matched to the speakers you are
using.
• The filters (HPF/SUB-W LPF) that you can
use differ according to the Dolby Pro Logic II
mode setting.
Dolby Pro Logic II Filter
mode setting HPF
MUSIC/MATRIX Not adjustable Adjustable
OFF Adjustable
* 1 Adjustment is possible only when
"SUB-WOOFER" is set to "ON".
• The factory default setting is "THROUGH".
Filter adjustment
HPF (high-pass filter adjustment)
This filter cuts bass sound from the front and
rear speakers.
THROUGH 50Hz 80Hz
Set the filter matched to the speaker when
small-diameter speakers are used.
THROUGH
Set this when using speakers that can
generate bass.
SUB-W LPF (sub-woofer low-pass filter
adjustment)
This filter cuts treble sound from the sub-woofer.
THROUGH 50Hz 80Hz
Set the filter frequency to match the sub-woofer.
THROUGH
Set this when a low-pass filter built-in
powered sub-woofer is used.
1. Press the [A] button to set to the adjust
mode.
ON
SUB-W LPF* 1
Adjustable
120Hz
120Hz
45
DXZ948RMP