Clarion DXZ948RMP Manual De Instrucciones página 10

AC-Processor III Operations
3. Touch on the ON/OFF display.
The position effect is toggled ON/OFF.
POSITION MODE
RTN
FRONT
BASIC
BU
3
OFF
B / U
When the position effect is set to "OFF", the
position setting is not reflected on the music
source. This ends the position setting. Press
the [SOUND] button to return to the original
mode.
4. Touch B/U to select "BASIC".
POSITION MODE
RTN
FRONT
BASIC
BU
ON 3
B / U
Each touch of B/U toggles between "BASIC"
and "USER".
5. Touch on the position basic menu No.
to select the position basic menu.
Position basic menu
No. Display Name Seat Position
1 FRONT-L Front left seat
2 FRONT-R Front right seat
3 FRONT Front seats
4 REAR Rear seats
5 FULL SEAT All seats
6. Press the [SOUND] button to return to the
original mode.
Adjusting/storing positions
(user memory)
With user memory, pin-point setting of speakers
is enabled so that the same audio effect can be
obtained from each speaker up to all listeners
based upon the position basic menu. Up to 5
adjustment setups can be stored to user
memory.
T-ALIGN (time alignment):
The distance from the listener up to each
speaker can be entered in 2.3 cm steps, and the
time that the sound reaches the listener from
each speaker can be adjusted.
SP GAIN (speaker gain):
Adjusts the speaker output level. Adjust so that
the volumes that are output from each speaker
are all the same.
18
DXZ948RMP
1. Press the [SOUND] button.
2. Touch POSITION.
3. Touch on the ON/OFF display.
The position effect is toggled ON/OFF.
4. Touch B/U to select "BASIC" or "USER".
5. Touch on the right of the display to
select the menu that is used as the menu for
adjustment.
6. Press the [A] button.
7. Touch on the left of the display to
select "T-ALIGN" or "SP GAIN".
8. Touch on the centre of the display to
select each adjustment item.
Each touch of switches the
adjustment items as follows:
Adjustment items
FRONT L SP (front left speaker)
FRONT R SP (front right speaker)
REAR L SP (rear left speaker)
REAR R SP (rear right speaker)
(when "SP-SETTING" is set to
"CTR+SW")
1
SUB-WOOFER (sub-woofer)*
(when "SP-SETTING" is set to
"SW L + SW R ")
1
SUB-W L (sub-woofer Lch)*
2
SUB-W R (sub-woofer Rch)*
* 1 This is displayed only when "SUB-
WOOFER" under "SOUND" in the adjust
mode is set to "ON".
* 2 This is displayed only when "SUB-
WOOFER" under "SOUND" in the adjust
mode is set to "ON", and "T-ALIGN" is
selected at step 7.
9. Touch on the right of the display and
adjust the item as desired.
POSITION EDIT
RTN
FRONT L SP 085 . 1cm
T-ALIGN
∗ "T-ALIGN" can be adjusted within the
range 0 cm to 501.4 cm in 2.3 cm steps.
∗ "SP GAIN" can be adjusted within the
range -20dB to 0dB.
10. Repeat steps 7 to 9 to adjust the desired
item.
11. When you have finished adjusting each item,
touch RTN.
The display returns to the original screen,
and " " is displayed at the BASIC or USER
display.
Operation so far completes position
adjustment. To continue to store the
adjustment values to the position user menu,
perform the following.
12. Touch and hold RTN for 1 second or longer.
The position menu list is displayed.
13. Touch and hold the user memory you want
to store the adjustment values to for 2
seconds or longer.
You will hear a long beep, and the values
you adjusted up to step 10 are stored to the
position user menu.
If you hear a short beep, the adjustment
values up to step 10 are discarded. Adjust
these values again as required.
14. Touch RTN.
15. Press the [SOUND] button to return to the
original mode.
∗ To select a stored user memory, touch B/U
to display "USER" and touch of on
the user memory No.
Selecting the VSE menu
VSE (Virtual Space Enhancer) allows you to
compensate the sound pressure balance inside
your car so that the same sound effect can be
obtained whichever seat you are sitting in as
proved in compensation simulations.
In the "Selecting each mode" procedure (cf.
page 44), set AC-PROIII to "STD".
• The factory default setting for VSE is "OFF"
and for the VSE basic menu is "FLAT".
VSE basic menu
Six basic menus are pre-stored to this function.
Select the basic menu to suit your preference.
1. Press the [SOUND] button.
2. Touch VSE.
OFF OFF OFF
VSE P. EQ Dolby PL II
RTN
SOUND MENU
2 - ZONE ADF A - MODE
OFF OFF
AC-Processor III Operations
3. Touch on the ON/OFF display.
The VSE effect is toggled ON/OFF.
VSE MODE
RTN
FLAT
BASIC
2 6
BU
OFF 1
B / U
When VSE is set to "OFF", the VSE setting
is not reflected on the music source. This
completes the VSE setting. Press the
[SOUND] button to return to the original
mode.
4. Touch B/U to select "BASIC".
VSE MODE
RTN
FLAT
BASIC
2 6
BU
ON 1
B / U
Each touch of B/U toggles between "BASIC"
and "USER".
5. Touch on the VSE basic menu No. to
select the desired VSE basic menu.
VSE basic menus
No. Function Name Description
Sound source flat
1 FLAT
equalizing
2 BASS BOOST Bass tones enhanced
Mid and treble
3 HIGH BOOST
enhanced
Low and treble
4 IMPACT
enhanced
Mid tones (human
5 ACOUSTICAL
voice) enhanced
Produces smooth-
6 SMOOTH
sounding tones.
6. Press the [SOUND] button to return to the
original mode.
Adjusting/storing VSE
(user memory)
User memory settings allow you to compensate
the sound pressure distribution to suit your
preference based upon the VSE basic menu.
Up to six user adjustments can be stored.
DIFFUSE:
Adjusts the deviation in diffused sound
pressure.
CAR WIDTH:
Adjusts the deviation in sound pressure along
the width of the car.
DXZ948RMP
19