Brush Replacement; Ce Declaration Of Conformity - Triton TTS 1400 Instrucciones De Uso

Replacing the saw blade
• Only use 165mm (6- ⁄ ") blades, with a kerf between 2.2 & 3.5mm (
1
2
for circular saws with a no-load speed rating of at least 5000min
• Never fit high speed steel blades or abrasive discs. Fitting of other purpose or different-
sized blades will void the warranty
• Do not fit inferior blades. Regularly check the blade is flat, sharp and free of cracks
or defects
See image E
1. Rotate the Mode Selection Lever (20) to Blade Change position
2. Press the Plunge Lock Button (2) and plunge the saw. The saw will lock at the depth that
allows access to the blade retaining bolt through the panel in the Blade Housing (22)
3. Fit the Hex Key (21) to the bolt and depress the Spindle Lock (19)
4. Turn the Hex Key in the direction of blade rotation (anti-clockwise) to undo the bolt and
remove the bolt and outer flange
5. Carefully lift the worn blade off the inner washer on the shaft and slide the blade out
through the aperture at the bottom of the Blade Housing and set aside
6. Carefully slide the new blade in through the bottom of the Blade Housing and position it
onto the inner washer on the shaft. The graphics should face out and the arrow on the blade
should point in the same direction as the arrow on the housing
7. Refit the outer blade flange then lightly screw the blade retaining bolt through the outer
blade flange
8. Check that the blade is seated properly, depress the Spindle Lock and tighten the bolt firmly
with the Hex Key
9. Depress the Plunge Lock Button to release the plunge lock and allow the blade to retract
fully into the housing
Cleaning
• Keep the tool's air vents unclogged and clean at all times
• Remove dust and dirt regularly with a cloth or soft brush
• Never use caustic agents to clean plastic parts. A damp cloth is recommended.
Water must never come into contact with the saw
• Re-lubricate all moving parts at regular intervals
Guarantee
To register your guarantee visit our web site at
www.tritontools.com* and enter your details.
Your details will be included on our mailing list (unless indicated otherwise) for
information on future releases. Details provided will not be made available to any
third party.
Purchase Record
Date of Purchase: ___ / ___ / ____
Model: TTS1400 Retain your receipt as proof of purchase

CE Declaration of Conformity

The undersigned: Mr Darrell Morris
as authorised by: Triton Tools
Declares that:
This declaration has been issued under the sole responsibility of the manufacturer.
The object of the declaration is in conformity with the relevant Union harmonisation
Legislation.
Identification code: 950638
Description: Plunge Track Saw
Conforms to the following directives and standards:
• Machinery Directive 2006/42/EC
• Low Voltage Directive 2014/35/EU
• EMC Directive 2014/30/EU
• RoHS Directive 2011/65/EU
• EN 60745-1:2009+A11
• EN 60745-2-5:2010
• EN 55014-1:2006+A1+A2
• EN 55014-2:2006+A1+A2
• EN 61000-3-2:2014
• EN 61000-3-11:2000

Brush replacement

⁄ " & ⁄ "), designed See image F and G
3 9
32 64
-1
• The carbon brushes are a consumable item which should be inspected periodically and
replaced when worn
1. With the saw disconnected from power, unscrew the Brush Access Caps (11). Remove the
brushes by pulling carefully on the protruding springs
2. If either brush is worn to less than 6mm (
genuine Triton replacement brushes, available from authorised Triton saw repair centres
3. Replace/refit the brushes, refit the Brush Access Caps and tighten firmly in place
Note: Triton Precision Power Tools will not be responsible for any damage or injury caused by
mishandling or unauthorised repair of this tool.
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer
functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),
with household waste
• Contact your local waste disposal authority for information on the correct way to dispose
of power tools
Triton Precision Power Tools guarantees to the purchaser of this product that if any part
proves to be defective due to faulty materials or workmanship within 3 YEARS from the
date of original purchase,
Triton will repair, or at its discretion replace, the faulty part free of charge.
This guarantee does not apply to commercial use nor does it extend to normal wear and
tear or damage as a result of accident, abuse or misuse.
* Register online within 30 days.
Terms & conditions apply.
t pr
ar This does not affect your statutory rights
Notified body: TÜV Product Service
The technical documentation is kept by: Triton Tools
Date: 25/05/2016
Signed:
Mr Darrell Morris
Managing Director
Name and address of the manufacturer:
Powerbox International Limited, Company No. 06897059. Registered address: Powerbox,
Boundary Way, Lufton Trading Estate, Yeovil, Somerset, BA22 8HZ, United Kingdom.
⁄ ") long, both brushes must be replaced using
15
64
oves to be defecti
GB
9