Adjustment Of The Detergent Solution Flow; Regulating The Forward Speed; Silent-Max Function; Vacuum Wand Kit (Optional) - Hillyard Trident R26SC Pro Manual De Uso

ADJUSTMENT OF THE DETERGENT SOLUTION FLOW

1
1
2
2

REGULATING THE FORWARD SPEED

1
1
2

SILENT-MAX FUNCTION

This machine has a silent-max function for reducing the noise generated by the suction motor.
To activate or deactivate this function, just press the button (1) on the instrument panel for at least three seconds (Fig.1).
1
2
1

VACUUM WAND KIT (OPTIONAL)

Upon request, the machine can be fitted with the VACUUM WAND system that vacuums up the detergent solution more accurately.
To start it do as follows.
1. Lift the brush head body and press the "BRUSH HEAD CONTROL" button (1) on the control panel (Fig.1).
NB: as soon as the button (1) on the control panel is pressed, the green LED (2) ("BRUSH HEAD BODY WORK POSITION") will switch off (Fig.1).
2. Lift the squeegee body and press the "SQUEEGEE CONTROL" button (3) on the control panel (Fig.1).
N.B. : as soon as the button (3) on the control panel is pressed, the green LED (4) ("SQUEEGEE BODY WORK POSITION") will switch off (Fig.1).
3. Remove all the vacuum kit components from the storage compartment (Fig.2).
4. Assemble the steel extension tube (Fig.3).
5. Connect the vacuum tube (6) to the extension tube (5) (Fig.4).
6. Insert the vacuum brush (7) in the extension tube (5) (Fig.5).
4 2
3 1
1
7. Remove the vacuum tube (8) from the sleeve (9) in the squeegee body (Fig.6).
8. Connect the wand kit vacuum tube (6) to the squeegee vacuum tube (8) (Fig.7).
9. Activate the vacuum control kit by pressing the button (10) (Fig.8).
N.B. : As soon as the button (10) is pressed, the LED on it will light up (Fig.8).
N.B. : As soon as the button (10) on the control display is pressed, the symbol (11) will appear (Fig.9).
WARNING: never pick up solid matter such as dust, cigarette stubs, paper, etc.
CAUTION: never collect gases, explosive/inflammable liquids or powders, nor acids and solvents! These include gasoline, paint thinners and fuel oil (which, when mixed with the vacuum air, can form
explosive vapours or mixtures), and also non-diluted acids and solvents, acetones, aluminium and magnesium powders. These substances may also corrode the materials used to construct the machine.
CAUTION: if the machine is used in dangerous areas (e.g. petrol stations), the relative safety standards must be observed. It is forbidden to use the machine in environments with a potentially explosive
atmosphere.
To adjust the flow of detergent solution during work, proceed as follows:
1. During the first few working meters check that the amount of solution is sufficient to wet the floor, but not excessive to exit the splash guard.
2. If the amount of solution that comes out is not right, use the "+" and "-" buttons (1) on the control panel to adjust it (Fig.1).
N.B. : The flow of detergent solution on the brush can be adjusted to one of four levels, from 0 to 3. The level can be seen with the symbol (2) on
the control display (Fig.2).
N.B. : If the flow is set to 0, there is no emission of detergent solution.
To adjust the flow of detergent solution during work, proceed as follows:
1. During the first few metres, check that the forward speed is adequate to the grip conditions.
2. If the forward speed does not suit you, you can control it using the "+" and "-" buttons (1) on the control panel (Fig.1).
N.B. : the forward speed can be adjusted at three levels from 1 to 3. The level can be seen with the symbol (2) on the control display (Fig. 2).
N.B. : the machine forward speed can also be adjusted by regulating the potentiometer in the control panel. To do this, press the dead man's
lever (2) to the required degree. The more you press, the higher the speed (within the limits of the level selected beforehand).
2
N.B.: when the silent-max function is active, the relative LED (2) will light up on the control panel (Fig.1).
3
2
6
5
4 5
19
7
5