Troubleshooting - Stanley SHP 1900 Manual Del Propietário

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

TROUBLESHOOTING

If you have any questions regarding the product, please call customer service at 1-866-508-1330.
PROBLEM
Unit will not turn on.
The high pressure
(HP) hose will
not connect/stay
connected to the
spray gun. Is this a
spray gun problem?
The unit is running
but there is no water
flow.
Why is water leaking
where the high
TROUBLESHOOTING
pressure hose connects
to the spray gun?
I can't remove the
lance from the spray
gun. What should I
do?
The power washer
turns on for 2
seconds, shuts off,
and will not turn
back on. Do I have a
defective unit?
93904_16ANR029_Stanley 1900PSI ENG-FR-SP.indd 15
CORRECTIVE ACTION
1. The GFCI module on the end of the power cord must be plugged directly into an
outlet.
2. Do not use an extension cord.
3. With the GFCI Connected make sure the power switch is turned on.
Note:
When power switch is turned on, the power washer will turn on by itself for 1-2
seconds and shut off. This is normal.
1. In most cases, the spray gun is not the problem. The problem is the rubber sleeve
covering the fitting at the end of the high pressure hose. It has likely slipped up
toward the metal tip. To fix: wiggle, twist and/or pull the rubber sleeve down until the
entire tip is visible plus an 1/8 in. of the metal fitting below the tip. Now try to insert
the hose tip into the spray gun. It should "click" into place and will not come out until
the hose is released by pushing in the lever on the underside of the gun. You may cut
away the end of the sleeve with a sharp knife if unable to move the sleeve down. Be
careful not to cut or puncture the hose.
2. Do not push in the release button when connecting the high pressure hose.
1. Check the water source. Unclog the nozzle on the lance. (See nozzle cleaning
instructions under "Cleaning nozzles".) Or take off the lance and just spray out of the
spray gun. This will indicate if the problem is with the lance.
1. Make sure there is an o-ring at the end of the metal tip of the high pressure hose.
If no o-ring is present, the connection between the hose and spray gun will leak.
O-Ring replacements are included in the package contents.
1. All lances and the detergent bottles are attached and removed from the extension
lance in the same manner. Insert the quick-release end of the lance/detergent bottle
into the extension lance. Press the extension lance and lance together (about a 1/8")
and turn clockwise. The lance will lock in place. Remove the lance by reversing this
procedure. Press the extension lance and lance together and turn counter clockwise.
The lance will slide out.
2. Or, hold the extension lance and lance in an upright position with the nozzle end
on the floor. Push the whole assembly straight down to loosen the connection,
and then follow the removal process again. You may also spray soapy water or a
lubricant in the area where the lance connects to the extension lance.
1. It sounds like your power washer is working just fine. When the water is connected,
the accessories are assembled properly, and the power switch is turned on, the power
washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts off
and waits for the spray gun trigger to be pressed. When the trigger is pressed, water
starts flowing through the pump. The water sensor in the pump "senses" the moving
water and automatically turns the power washer on.
2. Turn the power switch to off, hold in the trigger on the spray gun, so that you have a
steady stream of water. While you are holding the trigger open on the spray gun, at
the same time, turn the power switch on.
15
16/12/14 下午5:47

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido