ROBBE Charterte Instrucciones De Montaje página 8

Fig. 35
- Glue the former R 13 to the nose of the fuselage as
shown.
- Install the motor mounts R 14 and the motor bulkhead R
15.
- Glue the in-fill blocks R 16 on both sides.
Fig. 36
- Glue the nose former R 17 in place as shown; ensure that
the holes for the motor retaining screws in the ply
bulkhead remain accessible.
Fig. 37
- Glue together the wing retainer plate R 18 and the doubler
R 18a with their edges flush.
- Glue the wing retainer plate R 18 to the fuselage together
with the reinforcements T 19.
Fig. 38
- Install the fuselage formers R 0 and R 1 "dry" (no glue),
pulling the fuselage sides in to meet at the tail. Check that
Assembling the model, receiving system and electric power system, final work
Part Description
No.
RC 4 Servo
RC 5 Servo output lever
RC 6 Pushrod
RC 7 Guide tube
RC 8 Aileron pushrod
RC 9 Captive nut
RC 10 Plastic screw
RC 11 Main undercarriage unit
RC 1 Wheel
RC 13 Collet and grubscrew
RC 14 Sleeve
RC 15 Brushless motor
RC 16 Socket-head cap screw
RC 17 Shakeproof washer
RC 18 Propeller driver
RC 19 Propeller
RC 0 Brushless speed controller
RC 1 Receiver
RC  Flight battery
Assembly and operating instructions
Charterle
the fuselage remains symmetrical when viewed from
above.
- Glue the tail end of the fuselage sides together.
- Glue the formers R 0 and R 1 to the fuselage sides.
Fig. 39
- Glue the fuselage turtle deck sheeting panels R  and R
3 in place, checking constantly that the fuselage remains
straight: check this over the plan.
Figs. 40 and 41
- Glue the bottom fuselage sheeting panels R 4, R 5, R
6 and R 7 together as shown.
Fig. 42
- Glue the assembled bottom sheeting to the fuselage.
Fig. 43
- Glue the windscreen frame R 8 and the nose sheeting
panel R 9 to the fuselage.
Material
---
---
Steel wire
Plastic
Steel wire
Steel
---
Steel wire
Plastic
Brass / steel
Brass
---
Steel
Steel
Aluminium
Plastic
---
---
---
Dimensions No. off
Ready made , N.I.
Ready made , with RC 4
0.8 Ø x 360 
300 long 
0.8 Ø x 55 
M4 1
M4 x 5 1
 Ø x 50 1
51 Ø 
. Ø x 7 Ø x 5 4
. Ø x 3 Ø x 14 
Ready made 1, N.I.
M x 5 
 Ø x 4.3 Ø 
Ready made 1, N.I.
8 x 3.8" 1, N.I.
Ready made 1, N.I.
Ready made 1, N.I.
Ready made 1, N.I.
8
Figs. 44 and 45
- Assemble the battery hatch from parts R 30 and R 31 and
trim it to fit on the fuselage.
Fig. 46
- Round off the fuselage nose as shown in the photo.
Figs. 47 and 48
- The entire fuselage can now be rounded off.
Fig. 49
- Glue the plastic latch to the underside of the hatch, taking
care to keep it central.
Note: the pushrod support R 3 and the tailskid R 33 are
not fitted until the model has been covered. The main
undercarriage should also be installed after covering is
complete.
Fig. 50
- Place the hatch on the fuselage and check that the latch
works correctly; you may need to make minor adjust-
ments to the hole in the former R 13.
No.
3279