Service And Repairs; Disassembly And Exchange - Aventics ECS10 Serie Instrucciones De Servicio

AVENTICS | ECS | R412004317–BDL–001–AE | English
3. Apply +24 V DC at the IN1/GN connection.
The "vacuum ON" (suction) process is interrupted, regardless of the switching
state of the internal regulator.
Solenoid valve "vacuum": LED lit (for ECS...20/30, the LED is integrated in the
CN1 electrical connector).
4. Apply +24 V DC at the IN2/YE connection.
The "release pulse ON" (blow off) process is activated with a simultaneous
interruption of "vacuum ON" (suction), regardless of the switching state of the
internal regulator. The GN connection does not need to be occupied for this sequence!
Solenoid valve "release pulse": LED lit (for ECS...20/30, the LED is integrated in
the CN1 electrical connector).
Pressure sensor presettings:
ECS...D (PE3-P2)
Output signal OUT 1 Switching function
Mode
Switching point
Hysteresis
Output signal OUT 2 Switching function
Mode
Switching point
Hysteresis
ECS...E (PE3-PV)
Output signal OUT 1 Switching point
Hysteresis
Recommissioning after shutdowns
1. Switch the operating voltage on.
2. Switch the working pressure on.
7

Service and Repairs

Cleaning and servicing
Penetration of contamination and fluids can lead to malfunctioning.
This no longer guarantees the safe function of the ejector.
O Maintain the highest standards of cleanliness when working on the
pneumatics system.
O Do not use high-pressure cleaners.
1. Close all openings of the ejector using suitable protection caps or equipment.
2. Check that all seals and plugs for the plug connections are firmly fitted so that no
moisture can penetrate into the ejector during cleaning.
3. Only clean the ejector using a damp cloth made from a non-fiber-releasing fabric.
Only use water and, if necessary, a mild detergent.
Maintenance
The ejector is maintenance-free if used as intended.
Replacing wear parts
12
The wear parts of the ejector are marked in Fig.
O Replace the wear parts if contaminated.
O Use the part numbers listed in this table to order wear parts from AVENTICS.
Wear parts
Filter insert ECS-10/-15
Filter insert ECS-20/-30
Silencer ECS-10/-15
Silencer ECS-20
Silencer ECS-30
Spare parts
Further information can be found on the Internet at
www.aventics.com/pneumatics-catalog
8

Disassembly and Exchange

Danger of injury if disassembled under pressure or voltage!
Injuries and damage to the product or system parts may occur if the pressure and
voltage are not switched off before beginning disassembly.
O Make sure that the relevant system parts are not under pressure or voltage.
NO
Hysteresis
750 mbar
150 mbar
NO
Hysteresis
550 mbar
10 mbar
750 mbar
150 mbar
NOTICE
12
.
Part number
1829207066
1829207067
1827000036
1827000037
1827000038
CAUTION
13
I+II
Exchanging filter insert or filter housing
1. Loosen the mounting screws (1).
2. Remove the filter housing (4) with filter insert (5).
3. Remove the filter insert (5) from the filter housing (4).
4. Remove the seal (3) on the filter housing (4)
(only for exchanging filter insert).
5. Insert the new seal (3) into the sealing slot. Check that the seal (3) is fitted correctly.
6. Press the filter insert (5) into the holder (6) (only use a new filter insert when
replacing filter insert).
7. Place the new filter housing (4) with filter insert (5) on the ejector (2). Check that
the filter insert (5) is fitted correctly.
8. Tighten the new mounting screws (1) (M
Mounting screws (1) (DIN EN 7045): ECS...10/15: 2 M3x12; ECS...20/30: 4 M3x12
13
III
Exchanging the silencer
1. Loosen the mounting screws (1).
2. Remove the silencer housing (3) with cover (4).
3. Place the new silencer housing (3) with cover (4) on the ejector (2).
4. Tighten the new mounting screws (1) (M
(DIN EN 7045): ECS...10/15: 2 M3x40; ECS...20: 2 M3x60; ECS...30: 2 M3x75
14
Exchanging the pressure sensor
1. Remove the exhaust tube (4) from the exhaust plug (5).
2. Loosen the tube nut (3).
3. Remove the plug (2) from the pressure sensor (6).
4. Loosen the mounting screws (1).
5. Remove the filter housing (11) with filter insert (12).
6. Loosen the mounting screws (8).
7. Remove the pressure sensor (6) with seal (7).
8. Place the new pressure sensor (6) with seal (7) on the ejector (9).
9. Tighten the mounting screw (8) (M
10.Place the new filter housing (11) with filter insert (12) on the ejector (9).
Check that the filter insert (12) is fitted correctly.
11.Tighten the mounting screws (1) (M
Mounting screws (1) (DIN EN 7045): ECS...10/15: 2 M3x12; ECS...20/30: 4 M3x12
12.Insert the plug (2) in the pressure sensor (6).
13.Tighten the tube nut (3).
14.Attach the exhaust tube (4) to the exhaust plug (5).
15
Exchanging the solenoid valve for "vacuum/release pulse"
(only ECS...20/30)
1. Loosen the mounting screws (2).
2. Remove the electrical connector (1) with seal (3) from the solenoid valve (4).
3. Loosen the mounting screws (7).
4. Remove the solenoid valve (4) with sealing plate (6) and gasket (5).
5. Place the new solenoid valve (4) with sealing plate (6) and gasket (5) on the
ejector (8). Check that the sealing plate (6) and gasket (5) are fitted correctly.
6. Tighten the mounting screws (7) (M
7. Connect the electrical connector (1) with seal (3) to the solenoid valve (4).
8. Tighten the mounting screw (2) (M
16
Exchanging the connecting cable with socket (only ECS...10/15)
1. Release the detent lever (2) and simultaneously remove the industrial plug (1)
from the solenoid valve (3).
2. Loosen the wires.
3. Connect the new industrial plug (1) until the detent lever (2) engages in the
solenoid valve (3).
4. Connect the wires.
17
Exchanging the CN1 electrical connector (only ECS...20/30) – form C
1. Loosen the mounting screws (2).
2. Remove the electrical connector (1) with seal (3) from the solenoid valve (4).
3. Loosen the wires.
4. Connect the new electrical connector (1) with seal (3) to the solenoid valve (4).
5. Tighten the mounting screw (2) (M
6. Connect the wires.
18
Exchanging the CN1 connecting cable – M8
1. Loosen the tube nut (2).
2. Remove the plug (1) from the pressure sensor (3).
3. Loosen the wires.
4. Connect the new plug (1) to the pressure sensor (3).
5. Tighten the tube nut (2).
6. Connect the wires.
16 18
Exchanging the ECS...10/15 cable set
16
1. Release the detent lever ( , 2) and remove the industrial plug (
16
solenoid valve ( , 3).
18
2. Loosen the tube nut ( , 2).
18
3. Remove the plug ( , 1) from the pressure sensor (
= 0.8 Nm).
A
= 0.8 Nm). Mounting screws (1)
A
= 1 Nm).
A
= 0.8 Nm).
A
= 0.8 Nm).
A
= 0.4 Nm).
A
= 0.4 Nm).
A
16
18
, 3).
8
, 1) from the