Hammerdrilling - BTI BH 5-45 ME Instrucciones De Manejo

E N G L I S H
Proper Hand Position (fi g. 6)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side
handle (c), with the other hand on the main handle (d).
Switching On and Off (fi g. 1)
To turn the tool on, depress the trigger switch (a).
To stop the tool, release the trigger switch.
The lock-on slider (b) allows the trigger switch (a) to be
locked on in chiselling mode only. If the lock-on button
is activated in drilling mode, as a feature the tool will
switch off automatically.
To turn the tool on, press the trigger switch (a).
To stop the tool, release the switch.
For continuous operation, press and hold down the
switch (a), slide the lock-on button (b) upwards and
release the switch.
To stop the tool in continuous operation, press the
switch briefl y and release it. Always switch off the tool
when work is fi nished and before unplugging.

Hammerdrilling

To turn the tool on, press the on/off switch (a).
To stop the tool, release the switch.
Drilling with a Solid bit (fi g. 1)
1. Insert the appropriate drill bit.
2. Set the mode selector switch (f) to the
hammerdrilling position.
3. Set the electronic speed and impact control dial
(g).
4. Fit and adjust the side handle (c).
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the
tool.
7. Always switch off the tool when work is fi nished
and before unplugging.
Drilling with a Core Bit (fi g. 1)
1. Insert the appropriate core bit.
2. Assemble the centerdrill into the core bit.
3. Set the mode selector switch (f) to the
hammerdrilling position.
4. Turn the electronic speed and impact control dial
(g) to a medium or high speed setting.
5. Fit and adjust the side handle (c).
6. Place the centerdrill on the spot and switch on
the tool. Drill until the core penetrates into the
concrete approx. 1 cm.
7. Stop the tool and remove the centerdrill. Place the
core bit back into the hole and continue drilling.
8. When drilling through a structure thicker than
the depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals.
To avoid unwanted breaking away of concrete
around the hole, fi rst drill a hole the diameter of
the centerdrill completely through the structure.
Then drill the cored hole halfway from each side.
9. Always turn the tool off when work is fi nished and
before unplugging.
Chipping and Chiselling (fi g. 1)
1. Insert the appropriate chisel and rotate it by hand
to lock it into one of 18 positions.
2. Set the mode selector switch (f) to the hammering
only position.
3. Set the electronic speed and impact control dial
(g).
4. Fit and adjust the side handle (c).
5. Turn the tool on and start working.
6. Always turn the tool off when work is fi nished and
before unplugging.
MAINTENANCE
Your BTI power tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
WARNING: To reduce the risk of injury,
turn unit off and disconnect machine
from power source before installing and
removing accessories, before adjusting
or changing setups or when making
repairs. Be sure the trigger switch is in the
OFF position. An accidental start-up can
cause injury.
This machine is not user-serviceable. Take the tool
to an authorised BTI repair agent after approximately
150 hours of use. If problems occur before this time
contact an authorised BTI repair agent.
Brushes (fi g. 3)
The carbon brushes are not user-serviceable. Take the
tool to an authorized BTI repair agent.
The yellow brushwear indicator LED (r) lights up when
the carbon brushes are nearly worn out. After a further
42