Technical Data - Hilti WSC 55 Manual De Instrucciones

WSC 55 hand-held circular saw
1 Cutting depth adjusting lever
2 Angle adjustment clamping screw
3 Parallel guide clamping screw
4 Cutting line indicator
5 Parallel guide
6 Baseplate
7 Inner clamping flange
8 Spindle
9 Riving knife
10 Spindle lockbutton
11 Screw
12 Clamping flange
13 Pivoting guard
14 Riving knife fastening screws
Noise/Vibration information
Measured values determined according to EN 50144.
Typically, the A-weighted sound pressure level of the tool is less than 98.5 dB (A).
The A-weighted permanent noise level/pressure of the tool is less than 111 dB (A).
Wear ear protection.
The typical weighted acceleration is 2.5 m/s
Right of technical changes reserved
EG declaration of conformity
Description: Hand-held circular saw
Designation: WSC55
We declare, under our sole responsibility, that this product complies with the following
standards or standardization documents: EN 50 144-1, EN 50 144-2-5, EN 55 014-1,
EN 55014-2, EN 61000-3-2, EN 61000-3-3 and according to the provisions of the directives
73/23/EEC, 89/336/EEC, 98/37/EC.
Hilti Aktiengesellschaft
Dr. Joachim Schneider, Leiter BU-Wood
Printed: 07.07.2013 | Doc-Nr: PUB / 5071327 / 000 / 00
15 Extraction system adapter
16 Chip ejector
17 Switch-on interlock
18 On/off switch
19 Hexagon socket wrench
20 Ventilation slots
21 Cutting angle scale
22 Cutting depth scale
23 Cutting depth locking device
The accompanying list of safety precautions
and the applicable regulations issued by your
trade association must be observed.
2 .
Serial no.: 00000000–99999999
Year of design: 1998
Dr. Andreas Dieterle, Leiter F & E Wood

Technical data

Power input:
Power output:
Spindle speed under no load:
Spindle speed under load:
Blade peripheral speed under no load:
Blade peripheral speed under load:
Cutting depth at 0°:
Cutting depth at 45°:
Angular adjustment:
Maximum saw blade diameter:
Minimum saw blade diameter:
Blade mounting hole diameter:
Riving knife thickness (standard):
Dust extraction connector internal dia.:
Machine weight as per VDE 0740/T100:
Protection class as per EN 50144
Radio and television interference suppression as per EN 55014
Warranty
Hilti warrants that the tool supplied is free of defects in material and workmanship. This warranty
is valid as long as the tool is operated and handled correctly, cleaned and serviced properly and
in accordance with the Hilti Operating Instructions, all warranty claims are made within 12
months from the date of the sale (invoice date), and the technical system is maintained. This
means that only original Hilti consumables, components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or replacement of defective parts only. Parts
requiring repair or replacement as a result of normal wear and tear are not covered by this
warranty.
Additional claims are excluded, unless stringent national rules prohibit such exclusion. In
particular, Hilti is not obligated for direct, indirect, incidental or consequential damages,
losses or expenses in connection with, or by reason of, the use of, or inability to use the
tool for any purpose. Implied warranties of merchantability or fitness for a particular
purpose are specifically excluded.
For repair or replacement, send tool and/or related parts immediately upon discovery of the
defect to the address of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to warranty and supersedes all prior or
contemporaneous comments and oral or written agreements concerning warranties.
1100 W
630 W
4400/min.
2800/min.
37 m/sec.
24 m/sec.
0 to 55 mm
0 to 40 mm
0° to 45°
160 mm
150 mm
20 mm
1.2 mm
35 mm
4 kg
Z / II
9