Single Safety Inspection Before Commissioning - Nussbaum COMBI LIFT 4.50 S Instrucciones De Servicio

9.1

Single safety inspection before commissioning

i Copy, complete and leave in the inspection book
Test step
Model plate .......................................................
Operating manual ............................................
Label (e.g. warning label) ................................
Lockable main switch .......................................
General condition of lift ...................................
Cover condition ................................................
Condition/function ramps ................................
Condition/function rollover/rollback safety ...
Condition of the joint bolts and bearing seating
Condition of concrete floor (cracks) ..............
Fastening anchor torque ................................
Fastening screw torque ...................................
Load bearing construction (deformations, cracks)
Condition of weld seams .................................
Tight seating of all load carrying screws .......
Condition of load cable and hanging elements
Condition of cable rollers ................................
Unit condition ....................................................
Hydraulic oil filling level ....................................
Condition of hydraulic lines incl. screw fittings
Hydraulic system leak-tightness ......................
Cylinder condition ............................................
Condition wiper cylinder .................................
Piston rods surface condition ..........................
Condition of the catch bar .............................
Condition/function of catch magnet and catch
Paint condition ..................................................
Condition of electrical lines and plug connections
Condition of operating elements ...................
Function button "LIFT, LOWER" .........................
Function button "Lower into catch" ................
Function CE stop and warning signal ............
Function Rope slack switch in case of
under-surface situation chapter 9.3 ..............
Functional test system with vehicle ................
Condition sliding parts ......................................
Cover conditions ..............................................
*) Place a checkmark in the relevant, if a retest is required then check it again!
Safety inspection done on:
Performed by company:
Name, address of specialist:
Result of inspection:
______________________________
Signature of specialist
If requested to take care of deficiencies
Deficiency removed on:
(use a new form for reinspection!)
184
OK Defective
or missing
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
□
.................
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
□
Continued operation questionable, reinspection required
□
Continued operation possible, remove defects by ______________
□
No deficiencies, continue to operate
______________________________
Operating company signature
______________________________
OPI_COMBI LIFT 4.50/4.65 S PLUS AMS - HYMAX II 4500/4650 S PLUS AMS_V1.1_DE-EN-FR-ES-IT
Serial number: _______________________________
Post-
inspection
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
□ □
................ _______________________________
______________________________
Operating company signature
Remarks